What to do if the mouse sticks. Freezes, twitches, slows down, the mouse cursor works intermittently - why and what to do? Software errors and their elimination

Good day, readers.

Some users encounter a situation when the mouse cursor is stuck on a personal computer or laptop. To fix the problem, you need to find out the reasons due to which this happens. And there are many of them. In this case, it is necessary to take into account all the nuances, including the device to which the manipulator is connected.

The former are usually associated with accompanying software - drivers. In addition, internal system errors and rare conflicts between connected devices affect the correct operation. Or the wrong setting was simply made.

If all of the above can be fixed relatively easily, then hardware errors will be more difficult to "cure". These include the following ailments:

damage to the wire;

poor or missing power at the connection port;

problems inside the manipulator.

Hardware errors - elimination( )

Regardless of the version of the operating system installed on the computer, be it Windows 7 or Windows 10, the first thing you need to pay attention to is the integrity of the device itself. If suddenly external damage is clearly visible on the connected component, there is a considerable chance that a chip or other breakdown of contacts could occur inside the board. Unfortunately, in the absence of relevant knowledge and the necessary equipment, it will be extremely difficult to solve the problem.

Sometimes the manipulator turns off as a result of the failure of the connected cable. If you know exactly where the cliff is, there is a chance to fix the problem on your own, although it will not be the most aesthetic. So, you need to turn off the component, cut out the problem section of the wire. Then strip the contacts on the two parts of the cord and connect the corresponding cores to each other. After that, it is imperative to close each separate "twist" with insulating material - usually adhesive tape is used. And after that, everything is hidden under the shrink wrap. Although, of course, it will be more convenient to use the same electrical tape.

Personally, I have restored mice from different manufacturers in this way several times. Of course, this cannot guarantee a long term "life" of the component in the future. So after such operations it is better to look for a new element. Until then, you can do with “ resurrected»Manipulator.

In some cases, the computer automatically turns off the power to the USB port to which the mouse is connected. And on laptops, this situation is more common than on stationary machines. As a result, the element we need does not fulfill all the prescribed functions. To check the situation in Windows 8 and other operating systems of the nearest versions, you must perform a number of actions:

It is worth noting that the same method works for Windows XP as well.

Software errors - elimination( )

It must be said right away that problems of this kind appear more often. The fact is that most of modern manipulators are automatically determined by the operating system, which is not always an excellent option, since some gadgets have their own characteristics. Therefore, the standard drivers provided in the system simply do not fit.

What to do in this case? You need to use the solution that comes with the item. Or look for the necessary software on the official website. This usually fixes the problem.

Problems with the freezing of the manipulator can be itself. To fix the problem, it is necessary to identify its cause as accurately as possible. This is sometimes very difficult to do. That is why, if possible, all the nuances should be taken into account. This is especially true for laptops - with compact laptops, this type of problem occurs most often.

Freezes reasons

All reasons for the freezing of the manipulator on the computer can be divided into two main types:

hardware;
software.

Software malfunctions are most often associated with drivers, as well as some errors within the system, a conflict between the installed hardware. Hardware errors are usually much more complicated, and their number is also much higher.

Hardware reasons for freezing a personal computer include:

If there is a check mark there, then you need to remove it. The PC may just turn off the mouse to conserve electrical energy. In addition, you should carefully inspect the USB connector itself as closely as possible. It often happens when it is poorly soldered on low-quality boards. And with careless handling, the legs of the contacts simply break.

Software errors: solutions

Hardware problems are much less common. In most cases, the software is to blame. Most modern USB mice are usually self-identified by the Windows operating system and installed. But this is not always good, since some gadgets have their own specifics. And the standard generic driver doesn't work for them.

If the manipulator freezes, you should use the software provided by the manufacturer in the kit with the mouse. Or download the official drivers from a reputable resource. In very many cases, this helps to resolve these types of problems.

If, after installing new drivers, the hangs persist, then you should check the "device manager". If there are icons next to which there is a question / exclamation mark, you need to reinstall them.

Mouse setup and calibration is carried out as follows:

The driving speed may be set too low. You can check this parameter in "Pointer parameters".

There are a very large number of problems that can cause the impossibility of normal operation of the manipulator. It is imperative to check all of them - this is the only way to get rid of freezes. First of all, you should pay attention to the drivers.

Despite its outward simplicity, it is the same complex composite device as other parts of the computer. And, of course, it is also prone to breakage if handled roughly. There is a certain tensile strength, upon reaching which the mouse breaks down. Often the malfunction manifests itself in the fact that the mouse cursor stops working.

Freezes

There are several types (symptoms) of impaired performance. The first is the problem that the mouse cursor hangs. There can be a fairly large number of reasons for the appearance of such a malfunction. Let's look at purely mechanical influences first. Sometimes, when working at a computer, the mouse cursor either starts to shake or just stop in place. That is, it simply ceases to obey the user. In most cases, the user is to blame for this.

The problem may arise due to lack of neatness and cleanliness in the workplace. There are several options for correcting this situation. First, clean the table, wipe off all dust from the surface, wipe with a damp cloth. Then gently clean the "eye" of the mouse - the area where the laser touches the surface. If this does not help, then carefully unscrew the mouse and clean it from the inside.
The mouse cursor can also freeze due to the fact that the whole system slows down. Moreover, this is not always a software error. If this is your home computer, try disassembling and dusting it. For this, either a special vacuum cleaner sold in computer stores, or an ordinary home vacuum cleaner, configured to blow out, is best suited. It may also be necessary to replace the thermal grease on the processor. But it is better to entrust it to professionals.

This is what we can do without touching the operating system of the computer. However, the source of the problem is not always clogging. Let's take a look at some bugs.

System

Often on the forums there are complaints: "I regularly shut down my computer abnormally. For some reason, the mouse cursor began to glitch." And really, why? Many users do not realize that they themselves bring the computer to an inoperative state. For example, constantly turning off your computer with the power button, you run the risk of creating a whole series of errors on the hard drive, including those affecting the mouse cursor. To fix this, you can use the CHKDSK system command. To do this, run or simply enter the command CHKDSK C: / F / R in the Run field in the Start menu. After that, a window will appear in which it will be said that to start the scan, you must restart the computer. Enter "Y" and press Enter. After that, restart the system through the "Start" menu. When asked if you want to cancel the disk check, don't click anything and wait.

Another variant

It is recommended to check the disk for errors as often as possible, this will avoid a number of problems associated not only with the mouse. If none of the error checking programs helped you, you can try reinstalling the drivers. To do this, either delete the old ones through the device manager, or download the utility for automatic updates. For example, you can try the free version of Driver Booster. If none of the above helps, try testing the mouse on a different computer. Perhaps her service life has come to an end.

"Cheshire"

In addition to freezing the cursor, there is another problem. Namely, the mouse cursor disappears. Just like in the previous case, there are several options why this might be happening.

If you are working in any browser and your cursor suddenly starts to disappear, try disabling some plugins in the browser. Specifically a flash player. Perhaps the problem lies in it, and not in the mouse itself.

Another option is a video card problem. Clean it from dust, check the performance of the cooling system.
Check the system for errors in the way that was indicated a little earlier in the article.
Reinstall drivers, plugins in browsers.
If the cursor disappears, do not rush to restart your computer. Just disconnect and reconnect the mouse to the connector.
There may be a check mark in the settings so that the cursor disappears when you type from the keyboard. In order to fix this, do the following: "Control Panel" - "Mouse" - "Pointer Options" - "Hide Pointer During Keyboard Input" - Uncheck the box - "Ok".
The problem might be a misconfigured OS. So just try changing the style. If it doesn't help, download third-party cursors and install them on the system.
Seven troubles - one RESET. The last resort is to reinstall the entire system. And preferably not the one in which the failure occurred.

Hopefully these tips will help you troubleshoot mouse cursor not working crashes.

In this article, I will tell you about three that will help you when working on your computer. I recently learned one of them myself.

So, as Gagarin said - let's go!

1. In Windows, you can quickly call up information about a file or folder as needed. That is, do not click with the mouse, but simply press two keys on the keyboard. And for this, you need to select the required file or folder and press the Alt + Enter key combination.

Don't believe me? Try it now. It really works!

2. Next, we will tweak the Google Chrome browser a little. When I did not know this trick, this guide ruffled my nerves himself. The problem was that when a tab hung in the browser, it was necessary, through the Windows task manager, to reset the entire Google Chrome program.

It was a shame that the other tabs contained useful information. I stumbled upon some useful resource, opened a link in another tab and it hung. And everything was gone!

But it turns out that you can "reset" only those tabs that are actually stuck. And the rest will remain in working, so to speak, condition. After all, each tab is a separate process, which can be disabled separately.

Google Chrome has a built-in task manager. Here we will work with him. You can call it by pressing the Shift + Esc keys. And a dispatcher window will appear in front of you, in which there will be a list of the names of all browser tabs.

After selecting the problematic tab, you just click the "end the process" button and move on.

3. Once my mouse for some reason began to live its own life. It was very inconvenient to move the cursor to the desired point - the cursor jumped in all directions and stubbornly did not want to move where I needed to.

I changed the rug, cleaned the mouse, but nothing helped. One small feature in Windows solved the problem. The fact is that all the information that goes from the mouse to the computer is stored in a special buffer.

By default, the length of such a packet is 100 units. It happens that the length of the buffer is relatively small. And that's why such troubles occur with the mouse. To fix this problem, you just need to increase the number of data packets.

This can be done as follows: in my XP start-control panel-mouse-hardware-properties-additional parameters.

On some versions of XP, the path is as follows: start-control panel-device manager-mice and other pointing devices... And with the right mouse button you need to click on the item of the device you need. In the drop-down menu, select "properties", then "others". And there already change the figure "100" to "150" or "200".
After such changes, your mouse will stop jumping in all directions and will unquestioningly perform your manipulations.

While working on your computer, you may encounter a problem such as freezing, jittering, or the disappearance of the mouse cursor. This can be explained by the fact that the device itself is faulty or there were malfunctions in the software.

If it freezes, the first thing that comes to mind is to check if the device wire is well inserted into the computer connector. It is possible that the USB port to which the mouse is connected is faulty, so you need to try to insert the plug into a different connector. To make sure that the device itself is malfunctioning, you need to take another mouse and check how the cursor moves when working with it.

It often happens that the mouse cursor disappears when foreign objects, pet hair, dust get into the optical connector. If you cannot remove them completely, the mouse needs to be disassembled and cleaned. To do this, you only need to unscrew one screw and remove the top cover. Any dirt inside should be removed, especially in the area where the beam hits.

If the mouse is wireless, you need to make sure that its batteries are not depleted and check the signal strength. Signals from other devices connected via USB ports may interfere with the pointer operation. In this case, the mouse cursor either freezes, not reacting in any way to movements, or periodically disappears and appears. In this case, connect devices such as a USB modem and a mouse from different sides of the computer. It is recommended to keep mobile phones away from a running PC.

If the mouse cursor slows down, this does not mean that the device itself is faulty. Perhaps you just need to increase the pointer speed. To do this, you need to go to the "Control Panel" through "Start" and open the settings tab in the mouse settings. Here you can change the cursor speed at your discretion, be sure to save the settings.

Freezing of the mouse cursor can occur due to the corruption of files of the system by viruses. In this case, you need USB through the "Control Panel" in the "Add or Remove Programs" section and install it again. You can find the USB driver online or download it from the disc that is sold with the mouse. After reinstallation, you need to check the operation of the device.

The mouse cursor may disappear or not respond to movement while working in the browser. If this happens only in the browser, then first you need to try reinstalling it.

If nothing has changed, then most likely the problem is in the Adobe Flash Player plugin, so it is suggested that you replace the old version with a more recent one. In addition, you can disable plugins in the browser settings, but then you will not be able to see flash images on the sites.

It happens that the mouse cursor freezes when there are a lot of processes running on the computer, which puts a heavy load on the memory and processor. In this case, it is recommended to disable unnecessary processes and remove them from automatic start.

Sometimes the problem of drawing the cursor can be solved by reinstalling the video card drivers, replacing them with newer versions.

In some cases, cursor hovering can be associated with the use of animated pointers. To get rid of the problem, you need to choose a standard cursor type.

There are two main reasons for slow computer performance. The first is directly related to its performance - if the desktop is old, it physically cannot work quickly with "heavy" ones. The picture on the screen is redrawn too slowly, the mouse may stop responding to manipulations, the hard disk indicator shows that the hard drive is loaded - the lack of RAM forces the system to actively use the paging file.

If the computer is old, the answer to the question - what to do if the computer slows down and the mouse freezes up - is very simple, you need to upgrade the system. The situation can be corrected by installing a more productive processor, a good video card, adding RAM.

The second reason for the slowness of the PC is the errors of the operating system. For all its merits, Windows is very unstable, its files can be easily damaged by viruses, power outages, and incorrect program operation. Typically, it is a software problem that causes your computer to run slowly. By removing them, you can return the system to its former performance.

Restoring normal PC operation

What if the computer slows down and the mouse jumps? First of all, you need to scan the system for viruses, having updated the anti-virus databases before that. Often, it is a viral infection that causes various failures during work.

Open the "Task Manager" by pressing Ctrl + Alt + Del, and evaluate which processes are the most loading the system. It is not uncommon to see that a particular process is using the CPU by 90 percent or more. If the name of the process is unfamiliar to you, search for its description in a search engine. Such an application must be removed. Check if it is in the startup folder, for this the easiest way is to use a free utility, and you cannot always find the cause of the problem. Therefore, in difficult cases, it is best to contact a service center for help. If your computer does not work well, call us - our specialist will perform the necessary repairs quickly, efficiently and for a minimal fee. The experience of our masters allows us to cope with any problems, you will be satisfied with the work with us. Don't waste time and effort on troubleshooting yourself - just dial our number and all problems will be a thing of the past!

Locking problems can be of many different types. To fix the problem, it is necessary to identify its cause as accurately as possible. This is sometimes very difficult to do. That is why, if possible, all the nuances should be taken into account. This is especially true for laptops - with compact laptops, this type of problem occurs most often.

Freezes reasons

All reasons for the freezing of the manipulator on the computer can be divided into two main types:

hardware;
software.

Hardware reasons for freezing a personal computer include:

The list of software faults is somewhat shorter:

Incorrect drivers installed (old version);
there was a conflict between different devices;
the mouse is configured incorrectly.

Video: Setting up your mouse - getting started

Hardware errors: solutions

The mouse freezes on the computer - what to do? First of all, you need to check whether it is intact. If the mouse has mechanical damage, then there is a high probability that the contact on the board inside has come off as a result of a strong impact. In the absence of a special soldering station, as well as skills, it is unlikely that it will be possible to eliminate this type of problem.

It often happens that the reason is a broken cable connecting the mouse to the USB / PS2 port. In this case, the easiest way is to purchase a new manipulator, since the repair of such a breakdown will cost about the same as purchasing a new device.

It often happens that the computer itself (especially with a laptop) turns off the power to the USB root hub. This renders the mouse inoperable.

To check this, you should proceed as follows:

Software errors: solutions

If, after installing new drivers, the hangs persist, then you should check the "device manager". If there are icons next to which there is a question / exclamation mark, you need to reinstall them.

Mouse setup and calibration is carried out as follows:

The driving speed may be set too low. You can check this parameter in "Pointer parameters".

Greetings!

At one point, the mouse cursor may begin to show instability in its work: freeze, intermittently move, freeze or slow down. In this article, we will consider the possible reasons for such an unpleasant behavior of the mouse pointer.

There may be several reasons, and we will try to understand what is wrong with it in terms of the accompanying "symptoms" that can also be observed.

1 reason for poor performance of the mouse cursor

Your computer is so busy that the system cannot allocate enough resources to keep your mouse cursor running smoothly.

In this situation, as a rule, it slows down not only the mouse cursor, but also the interface of the operating system itself and the programs launched in it.

Solution: you need to restart your computer. This is usually enough to restore normal mouse cursor operation. If this does not help and the former performance of the computer is not restored, then you should use it to a state when everything worked without brakes.

2 the reason for the "glitches" of the mouse cursor

All modern mice have an optical sensor, which determines the movement of the cursor by the user. However, not every surface is suitable for such mice. On some surfaces, the optical system used in the mouse is not always able to correctly detect the movement of the cursor properly. Hence, there are problems with lagging, friezes, etc.

Solution: Try using the mouse on a different surface. If the problem is solved, then you should use it on this particular surface or purchase a mouse pad, on which any optical mouse will work correctly, almost guaranteed.

3 reasons why the mouse cursor can slow down and glitch

Malfunction of the mouse itself. The fact is that over time, the cable that connects the mouse to the computer wears out. It disrupts normal electrical contact, which leads to malfunctions and even the disappearance of the mouse cursor from the system.

Solution: check this mouse by connecting it to another computer. If it shows instability in its work there, then this will confirm the existing fear of its breakdown. In this situation, it will need to be repaired or replaced with a new one.

4 reasons why the mouse does not work properly

If the mouse is wireless (radio or Bluetooth), then from time to time the cursor may jerk. This is due to the fact that the radio signal is less reliable than a wired connection. Especially often cheap wireless mice or those that come with the keyboard are "buggy".

Solution: in this situation, we recommend placing the USB receiver as close to the wireless mouse as possible, this should improve the stability of its operation. If you plugged the receiver into the USB port on the back of the computer, switch it to the front panel.

What to do if the mouse cursor is buggy? Below are 10 tips for solving this problem, annoying but not fatal.

1. The correct surface for the mouse

The mouse cursor can be buggy if the mouse itself is optical, and the surface for it is too transparent / mirrored. Use a rug, or a newspaper or book as a last resort.

2. Low battery

This tip applies to wireless mice. Make sure the battery is not depleted.

3. Special buttons

there are special buttons on the keyboard to change the speed of the cursor movement, check if they are jammed.

4. Plug into another USB port

Take this into account: it can test almost any device that works via USB. Suddenly, the problem is not with him, but with the computer? Try using it on another PC

5. Test your computer with a different mouse

Similar to the previous advice, the only difference is that here Mohammed is already walking towards the mountain. Replace the buggy mouse with another, 100% working one. The cursor stopped slowing down, huh?

6. Eliminate exposure to viruses.

Some malicious programs can “hit” such seemingly non-obvious places as the cursor. Check your computer

7. High temperature, etc.

You know, it's like a human being. If the arm is pricked, there may be heart problems. Obviously? Not at all! Same here: problems with the mouse cursor? It is not at all glitching, it's just that the temperature of the video card / other devices is too high. Check it out with Everest or Aida.

8. Add speeds, change settings

Sometimes it helps to increase the speed of the cursor. Go to the Control Panel - Mouse, in the “Pointer Parameters” tab, play with the settings.

9. Update drivers

You should update / reinstall the drivers for both the video card and the mouse itself, it is highly likely that the problems with the cursor will disappear. Note that I do not mention reinstalling windows - this is clumsy.

10. Get rid of dust

Both on the device itself and inside it. If it is not possible to disassemble the mouse, limit yourself to thoroughly cleaning the hole where the red LED is on. After all, even a small hair can cause cursor glitches.

aswin.ru

Why does the mouse cursor slow down? The main causes and options for their elimination

Hello dear readers.

Often on the Internet, you can meet users who complain that their mouse cursor slows down. At the same time, problems appear when working with simple applications, as well as large ones. It should be said right away that there are a lot of reasons for such symptoms. In the article I will try to outline all the possible ones, and of course I will indicate different solutions.

Mouse problems (back to table of contents)

As mentioned above, there are many reasons why the pointer slows down on the screen. The first thing to do is check the connected device itself. Or rather, find another device to connect it to the system. If the problems go away, they are in the manipulator itself. If not - in the main hardware or operating system.

In the case when the mouse is wired, make sure that the cable has not been bent. In addition, it is advisable to check the area of its connection to the board - sometimes it is at this point that you can observe a small gap. This leads to malfunctions.

For cordless mice, it's important to keep track of the battery level. Often, problems arise precisely because of dead batteries.

Also, there are often situations when dirt or hair from pets is simply stuffed into the optical element. Try to clean everything neatly. It is advisable, of course, in this case to untwist the device itself and clean it inside. If this does not help, let's go further.

Driver (back to content)

A mouse, like any other device connected to a computer, needs a driver. In most cases, the required program resides in the operating system itself. But in some situations it may be absent. Due to the lack of the required driver, the cursor moves in jerks.

The solution is simple - go to the official website of the manipulator manufacturer, download the required file and install it. You just need to choose the right operating system, be it Windows 7 or XP. In newer versions, this is rarely the case.

Operating system (back to content)

When your cursor starts to freeze and get lost, go to the "Task Manager" by pressing "Ctrl + Alt + Del", and look at the "Performance" tab, which is exactly in Windows 8 and Windows 10. We are interested in the tabs: "CPU" , "Memory", "Disk". If suddenly one of them shows an approach to 100% - this may well cause a problem.

The solution is to offload the operating system. To do this, check "Startup". Detailed information can be found in this article.

Also, view the applications you are using. Perhaps some of them are not needed for work - turn off.

In addition, check out the Speed-up and Optimization section. In it you will find a lot of useful information that affects cleaning the system as a whole.

If all else fails, it may be time to reinstall the OS.

Video card driver (back to content)

The corresponding element is responsible for the picture on the computer, which also communicates with the system using its own program. And if there are no necessary drivers, noticeable pauses of the cursor appear with a sharp movement of the mouse.

Installation of suitable software will help, which can be taken on the official website. If you do not know the manufacturer or model, use the program that allows you to independently find and update all drivers.

Sometimes the reason why the cursor slows down is poor heat dissipation as a result of contamination of the system unit or laptop. This is especially noticeable in games, for example, in tanks and similar online projects. True, most often such problems are accompanied by graphics slowdown. The same is often observed in the browser.

Clean and lubricate active elements.

Wi-Fi module (back to content)

Sometimes the problem may be the Wi-Fi module installed on the computer. It affects the wireless mouse with slight interference. Try turning it off. Or replace the mouse.

I hope here you will find the reason and its solution, due to which you are having problems with the manipulator. Subscribe and tell your friends about us.

windwix.ru

Why is my wireless mouse lagging?

Wireless mice use a radio link to connect to a computer. For this, the mouse is equipped with a transmitter and a battery, and a small receiver is connected to the USB port of the computer. Most of the problems with wireless mice are related to the quality of the wireless connection.

A poor-quality communication channel leads to unexpected failures (the cursor freezes and there is no reaction to pressing the mouse buttons), the mouse cursor may jerk or jump unexpectedly across the screen, and temporary cursor fading is also possible.

External radiation sources can affect the quality of the communication channel. These can be devices of electromagnetic radiation: microwave ovens, Wi-Fi devices (routers), built-in Wi-Fi modules and other wireless devices, a CRT monitor or TV.

Cheap wireless mice are most influenced by sources of electromagnetic radiation; they use only one communication channel. In more expensive models, several channels are used, that is, when interference appears, the device automatically switches to another communication channel, where interference does not affect the quality of communication.

It should be noted that the influence of other radiation sources depends to a large extent on their location to the computer. The closer to the workplace, for example, a Wi-Fi router is, the more influence it can have on the quality of the connection. In this case, care must be taken to keep sources of possible radiation as far away as possible.

Another important feature of wireless mice is the presence of a rechargeable battery to ensure the operation of the device. Many users forget about this very often, therefore, when the battery charge decreases, you can observe the deceleration of the mouse cursor on the monitor screen. The same goes for using the mouse over long distances. Wireless devices work reliably at distances of up to 15 meters, but in this case, power consumption is likely to increase and the battery will be discharged faster.

It should also not be forgotten that conventional alkaline batteries provide a 1.5V power supply, while rechargeable batteries are powered by only 1.2V. In this case, the wireless mouse will work longer, but its range will be reduced. There can be only one solution to power problems - replacing the battery. In some models, the battery may be built into the mouse and will need to be disassembled to replace it.

Low power problems can be encountered when using a USB extension cable to connect to a wireless receiver. The longer the cable is used, the less power can be transmitted through it. As a result, this negatively affects the operation of the manipulator. Therefore, if you find that your wireless mouse is slowing down, you should install the receiver directly into the USB port of your computer. Read about the types of computers.

If the computer is located on a conductive surface, then you may encounter the problem of "shielding" the receiver and the computer mouse. In this case, the signal from the mouse will simply not be perceived by the receiver. A way out of this situation is the use of insulating pads made of rubber, wood and other dielectric materials, it may even be time to think about purchasing a mouse pad. Also, problems with the mouse can occur due to incorrect drivers. When connecting a mouse to a computer, the system may not find a suitable driver for this mouse model and will automatically install the driver for a compatible computer mouse. In this case, the functionality and quality of the manipulator may decrease.

It is necessary to download the appropriate driver for a specific mouse model for the version of the operating system installed on the computer from the official website and install it yourself in order to eliminate possible problems with the software. Also, a disc with drivers and software may be supplied with the device, which you should definitely use.

The article lists the main reasons for the slowdown of a wireless mouse, but do not forget about regular cleaning. She, like a wired one, can simply get dirty, which is also the reason for her not working correctly.

ProComputer.su

5 proven reasons why a mouse freezes on a computer or laptop

The mouse is an integral part of any computer system, and since 1981, it has become the main tool for interacting with the operating system.

Therefore, it is not surprising when a mouse in a computer or laptop freezes and does not respond to anything, no matter for how long it freezes for a second, for a few seconds, periodically or constantly, it infuriates.

Unfortunately, such a problem exists and practically does not depend on the OS, be it windows xp, windows 7 or windows 10, especially if it is a wireless mouse.

Most often, the mouse cursor slows down and freezes due to her own fault. Why? Because consumers, as a rule, are guided by two criteria - price and wired or wireless.

It is not right. The choice of mouse is even more important than the choice of the keyboard and it is not easy to choose one, as a huge number of different types, shapes and models have flooded the market.

In this post, I will partially touch on the choice, since you may need to buy a new one after reading this guide.

The main part will relate to the topic of the article - why a wireless mouse often or sometimes freezes in a computer or laptop.

What is the difference between computer mice

There are two main types - optical and laser. Both technologies are very similar. Both use a beam of light that bounces off a surface and informs the computer about the position of the mouse.

Laser technology allows for much more precise interaction, which is why it is readily chosen by gamers and other users who need precise cursor guidance.

Laser also allows for higher DPI, which is especially important for gamers.

For the average user, dpi above 1000 is more than enough, and there are practically only such models on the market.

The advantage of optical technology is that it is simply cheaper. Even in the case of gaming models, the models are very similar to each other, differing only in the sensor and greatly in price.

If you want to work with your mouse on almost any surface, you must look at with a laser sensor.

Only on a sheet of glass or other transparent surfaces it will also not work, although there are exceptions, for example, the Logitech Performance Mouse MX is equipped with Laser Tracking technology, which allows it to be used on glass (with a thickness of 4 mm above), since the laser is so accurate. which can reflect the beam of microscopic glass imperfections.

Microsoft provides an alternative to optical and laser sensors with BlueTrack technology, using a wide beam of blue light.

It can work on any surface (except glass and mirrors) while maintaining accuracy. While not the best solution for hardcore gamers, office users will feel the difference in technology.

How I fixed the wireless mouse permanently freezing issue

It annoyed me to the point that my mouse constantly began to freeze for several seconds - in the center of the monitor, in the upper left corner, in a word, it happened everywhere - it hung and did not move.

I repeat, it started to freeze, it worked fine before, only I used it in a laptop.

I analyzed the situation, the only thing I noticed a difference was that when I was connected to a laptop I was next to it, and in the computer the distance increased to at least 1 meter and there were 2 obstacles in the way in the form of a side table wall and a computer table.

Then I bought a USB extension cable, as in the picture below, I connected the dongle to it and placed it near the mouse.

The miracle happened, the freezes stopped, the nerves calmed down, the work returned to normal, in a word, the mouse hung through a bad pairing.

The first reason why the computer mouse freezes is a weak sensor

If you have problems with the freezing of a computer mouse - it does not always respond to a key press, or a change in position, then the first thing you should check is the sensor.

The optical sensor reacts to objects that send a beam of light - which is why there is a movement and responsiveness of the cursor, which changes its position on the screen.

Keep in mind that it should not sit directly on glass or slippery surfaces.

In addition, it is worth cleaning the sensor, wheels and keys (you will need to disassemble) - a can of compressed air and a toothpick are ideal for this.

The second reason why the computer mouse freezes up - drivers

Problems related to the operation of your computer mouse can also be caused by the driver installed on your computer or laptop.

To uninstall and reinstall a pointing device driver, open Device Manager and locate the Mouse and other pointing devices section.

Then select the HID-Compliant Mouse, and RMB select the "Uninstall" option. After this procedure, restart your computer - the system will automatically install the default driver.

The third reason why a computer mouse freezes is USB ports

The problem can also be caused by the USB ports connected to the motherboard. If you still have not managed to solve the problem of the freezing of the computer mouse, you should check if the device is not damaged.

The easiest way would be to connect the mouse to another computer. So you can be sure that the problem is not with the device, but the cause should be looked for in the computer.

In addition, you can test the computer mouse in Safe Mode - to do this, at boot time, press the F8 key and select the Safe Mode menu item.

If it turns out that the mouse works as expected in Safe Mode, then the problem is probably in the system settings.

If the mouse is connected to the USB port on the front of the computer, try connecting it to the rear USB port. That's all. Good luck.

vsesam.org

Why does the mouse cursor freeze?

If the mouse cursor freezes, then the first thing that comes to mind is to check if the device wire is well inserted into the computer connector. It is possible that the USB port to which the mouse is connected is faulty, so you need to try to insert the plug into a different connector. To make sure that the device itself is malfunctioning, you need to take another mouse and check how the cursor moves when working with it.

Freezing of the mouse cursor can occur due to the corruption of files of the system by viruses. In this case, you need to uninstall the USB driver through the "Control Panel" in the "Add or Remove Programs" section and install it again. You can find the USB driver online or download it from the disc that is sold with the mouse. After reinstallation, you need to restart your computer and check the operation of the device.

The mouse cursor may disappear or not respond to movement while working in the browser. If this happens only in the browser, then first you need to try reinstalling it.
If nothing has changed, then most likely the problem is in the Adobe Flash Player plugin, so it is suggested to replace the old version with a more recent one. In addition, you can disable plugins in the browser settings, but then you will not be able to see flash images on the sites.

Sometimes the problem of drawing the cursor can be solved by reinstalling the video card drivers, replacing them with newer versions.

In some cases, cursor hovering can be associated with the use of animated pointers. To get rid of the problem, you need to choose a standard cursor type.