Modem D Link 2500U. How to configure the modem on the computer

General view of the modem:

Connectors and modem buttons:

Connection diagram:

Before starting the ADSL modem setting, you must check the correctness of the splitter connection (splitter is a device for separating a low-frequency signal of a regular telephone and high-frequency ADSL signal):

    In the cell labeled as Line - Connect the telephone line.

    In the cell labeled as Phone - Connect the telephone.

    In the cell labeled as Modem. - Connect the modem.

Splitter (top view):

AdSL modem setting

Step 1. Select "Start"\u003e Control Panel\u003e Network Connections. Press the right mouse button to connect ( please note that this is the Internet connection through ADSL modem, and not Bluetooth, Wi-Fi, etc.) and select " Properties»:

Step 2. In the tab " General»Highlight the component" Internet Protocol (TCP / IP)"And click" Properties»:

Step 3. Select " Use the following IP address"And fill in the fields as shown in the figure, then click on the" button " OK»:

Step 4. Open the window of your Internet browser, type in the address bar 192.168.1.1 and click on the button " Transition"(Either on the key" ENTER»):

Step 5. In the window, fill in the following fields:

    User: admin.

    Password: admin.

    After entering, click " OK»:

Step 6. In the window that appears, select the menu " Advanced Setup.»:

In the new firmware, the navigation panel on the options looks like this:

Do not be afraid and do not think that this instruction will not help you, since the difference is only that all options are visible in such a firmware. It is worth noting that all these options are located in exactly the same hierarchical order (indentation from the left edge), as well as if you personally opened them in an earlier version of the firmware.

Step 7. Turn the tick in the column Remove. and click on the button " Remove."(If there are no settings, immediately go to step 9):

Step 8. After removing the old settings, click on the " Save / reboot»:

Close the window of your Internet browser and wait a few minutes while the modem restarts.

Step 9. Repeat Steps 4-5. Remove the checkbox on the page " DSL AUTO-CONNECT"And set the following values:

Then click on the button " Next»:

Step 10. Select the connection type " Bridging."And install Encapsulation Mode - "llc / snap-bridging". Click on the "button" Next»:

Step 11. Install the checkbox, as shown in the picture and click on the button " Next»:

Step 12. Leave everything as it is and click on the button " Next»:

Step 13. To save the settings, click on the "button" Save / reboot»:

Close the window of your Internet browser and wait a few minutes while the modem restarts. Do not turn off the modem at the time of reboot !!!

Step 14. When the setup is completed, perform Steps 1-2. And set items as shown in the figure, not forgetting to approve the choice of the " OK»:

The modem is ready to operate.

Connecting to the Internet is carried out on various technologies and protocols. One of the first was the telephone line, remaining relevant until now. The technology that uses this type of communication is called ADSL2 +. At the moment it is replaced by more convenient and high-speed options, but in remote settlements is still one of the main ways for wired connection to the "World Wire Weight". Consider in detail the 2640U DSL router, providing a wireless connection to the Internet.

The 2640U router is used only to connect using ADSL technology.

For acquisition, four variations of this model are available. Externally, they are indistinguishable, the difference is only in the versions of hardware revisions. The DSL connection method is already outdated, but still relevant for remote settlements.

It also has a wireless network connection feature. That is, it is used as a Wi-Fi device. DSL-router D-Link 2640U characteristics are identical to other models from the XDSL segment.

The 2640U router interface does not contain USB connectors, which means there is no possibility to connect a 3G / 4G modem to it or perform the firmware through the "flash drive". It also does not support the creation of a VPN server, using as torrent or DLNA servers. There is no possibility to make an individual configuration or change the purpose of the buttons on the equipment.

Appearance

DSL Wi Fi-modem D-Link 2640U is a black box with rounded edges. On the front side there are light indicators with a signature signaling the operation of the current connection. The power connector and ports are on the back side along with the only antenna.

The design is the same as most routers from the manufacturer.

Included to DSL equipment go all the necessary cables to install the network device. The main documentation and configuration assistant are on the disk included in the package.

Connection and preparation for work

Before you configure the D-Link 2640U router, you must connect it to the electrical network. To do this, use the power adapter, which is included. Phone cable connector Insert into a special device - splitter. It will allow you to divide the signal that goes on the Wires, two: the first is responsible for the phone, and the second is for providing Internet access. The last step is to connect the 2640U network cable to the network port on the computer.

Settings

The configuration of the network device is performed in two ways. Using the installation wizard from the disk either through the browser in the router menu. Consider each of the options in more detail.

To configure a DSL wireless 2640U router in automatic mode, you must first start the "Installation Wizard", which is on the disc with a set of delivery. Next, you need to choose the country and the organization providing access services to the Global Network.

In the next step, you will need to specify the login and password provided by the provider at the conclusion of the contract.

After that, the router automatically performs the necessary actions.

Connecting to the Internet manually on the example of some providers

If the first option did not help, or the user prefers to configure independently, you must log in to 2640U through the browser.

Now consider how to configure the DSL D-Link 2640U router depending on the selected provider.

"Home ru"

Officially, "Dom.ru" does not support DSL routers, as they use outdated Internet connection technology. But the following instruction applies.

Connection type (Connection Type) Type on PPPoE. Interface (Interface), or Connection Port, DSL (NEW). Name (Name) - Enter any value. This is just the name of the DSL connection being created.

Section "ATM":

The value of the VPI and VCI fields responsible for the DSL connection must be found at the provider. They are individual depending on the region of residence and port on the equipment provider's equipment. The remaining fields are left unchanged.

Section "PPP":

In the field "username" (username) and "password" (Password), enter the data provided by the provider for the DSL connection service. The remaining parameters - no change.

To use the IPTV function, you must set a checkbox in the "Enable IGMP" checkbox (Enable IGMP Multicast).

Press the "Apply" button. In the top menu, select System (System), "Save and Restart" (Save and Reboot):

On this, the primary configuration of the Internet on D-Link 2640U is complete.

Rostelecom

The service provider officially supports this model. Adjusting the Rostelecom Provider DSL D-Link 2640U router is identical to the above method. This is explained by the fact that both providers use the same internet setup procedure.

"Beeline"

For DSL router Wi Fi D-Link 2640U Internet connection via the Beeline provider is not possible, since it is not directly able to support connection via VPN servers of the provider.

To use it, you must purchase a second network device capable of maintaining this function. It is also recommended to immediately select a model through which it is possible to configure optics for the DSL wireless home router D LINK 2640U.

NetBynet

ADSL WiFi-router D-Link 2640U is not supported by NetBynet as a router to provide access to World Wire Weight. Before configuring according to the instructions of the DSL D-Link 2640U router, it is recommended to first contact the provider for advice. This is due to the fact that NetByNet necessarily uses the identification by the MAC address of the network equipment.

Wireless network

SSID: Come up with Wi-Fi network name. Country: Specify the state of finding a user. Channel: leave AUTO mode.

Enabling the "Hide Access Point" function means that the connection is invisible when trying to find it in a general search. To connect to the Wi-Fi network, you will need to manually enter the name of the access point, specify the password to it.

The remaining parameters are left without adjustment. Press the "Apply" button to save the changes.

Network authentication is an encryption algorithm used to protect the wireless connection. It is recommended to set the WPA-PSK / WPA2-PSK value. These are the latest standards that are not hazardous. In the "Encryption key" field, come up with a password for access to Wi-Fi. The rules for its creation are indicated above, when the process of changing the password to the 2640U network device was described. "WPA Encryption": Install TKIP + AES to reliably protect the access point. The remaining fields are left unchanged.

  • Press the "Apply" button to save the configuration. Next, you will need to restart the DSL router to apply all changes made.

The above method will be able to pass the "Wi-Fi" to the 2640U router without special difficulties for the user.

Setup in repeater mode (repeater), amplifier, adapter or access point

The 2640U router is configured in different modes: Bridge mode, access point, repeater, or Wi-Fi signal amplifier. This will be discussed in separate instructions for setting up these options.

IPTV.

To configure IPTV on the DSL router, you must set the "Enable IGMP" configuration to the Internet connection. This was mentioned in the section of the article informing about the configuration of the DSL connection through the House.ru provider.

Then you should connect the TV-prefix with a power cable to the DSL router, perform the following steps in the Configuration menu:

Name: Come up with any name to connect. In the LANS section, mark the connector to which the TV prefix is \u200b\u200bconnected. In the WANS section - Bridge mode created earlier. Click "Apply."

Requires DSL equipment to save the configuration.

Dynamic DNS.

The 2640U network device supports the ability to set up a dynamic DNS server.

By default, DSL Wi-Fi Router Model 2640U proposes to use the DDNS address from the manufacturer. The user himself determines the most convenient service for it.

Security Settings (Antivirus, Firewall)

Then click "Apply", and then restart the DSL router so that the changes are preserved.

To enable the "Parental Control" function, you need to go to the "Control" menu, select the appropriate option. Next, click the Add button:

You must specify the following parameters. "Title": Come up with the name of the service. "Performance Days": Slide checkboxes in checkboxes for days for which this rule will act. The following two sections are responsible for the time interval with an accuracy of the minute, fill them. "MAC address": specify the physical address of the equipment for which this rule will be applied. Click "Apply." To use the parameters, the equipment is best restarted.

Setting up printer

The DSL modem cannot directly connect the printer. It is possible to use this equipment only to connect to the printer via the local network.

Possible malfunctions and ways to eliminate them

If the DSL router has problems, the first thing is to try to restart the device. Another option is to reset the settings to the factory. How to do it, is described below.

It is also worth remembering that cables can also be damaged. It is worth carefully checking all the switching on the equipment and devices connected to it. Sometimes there are situations where the problem is on the side of the Internet service provider. Then it is worth calling technical support, to get advice from experts.

If the DSL router still does not work, it is recommended to contact the service center. Masters diagnose the problem, help it solve.

Update firmware

Equipment over time is obsolete. In order to stop it longer, it is "flashing periodically". The manufacturer lays out fresh updates on the official website. For the 2640U model they download them to:

Last update dates back 2013. This means that this device is no longer supported by the manufacturer. Consider how you can update the DSL modem.

Via web interface

Through the "System" menu, item "Update by":

The window has two updates.


In the current example, the DSL "Wi-Fi" emulator of the 2640U network device is used, so the inscription is displayed on the screen: "Unable to check the availability of software updates."

Through a mobile application

There is also an update option through a mobile application. It exists for Android and iOS platforms.

Unfortunately, currently the 2640U model is not in the list of compatible devices. Accordingly, the user does not have the ability to produce this operation through a mobile application. The list is constantly updated, you can watch it in the app store.

RESET OF ROUTER SETTINGS TO FACTORY

Performing the settings on the device "DSL" 2640U is carried out in two ways. In the first case, it is enough to press the RESET button on the back side, while holding it for 10-15 seconds. The simultaneous reboot of all light diodes will show that the process is made.

The second option - through the web interface. To do this, select the "System" item in the upper left corner, hereinafter - "factory settings":

Within two minutes, the network DSL device will roll back to the factory configuration.

Output

DSL "Wi-Fi" Router D-Link 2640U is a model that supports outdated ADSL technology. It is suitable for work, mainly in remote settlements of the country, where in addition to the telephone line there are no other alternatives to the wired Internet.

To configure in the private house "D-Link" "DSL" 2640U is perfect. A pleasant and understandable interface, minimum of operations. Configuration is performed in 4 minutes.

pros

Network device 2640U refers to the line of budget DSL routers, that is, its price is acceptable.

It is possible to use in other modes other than a router. Excellent alternative as an access point

Minuses

Equipment uses XDSL connection technology rarely applied to date. For its performance on modern protocols, firmware is often required on third-party modes. However, this leads to the non-working state of the equipment.

The D-Link DSL-2500U router is used to connect one computer to the Internet using ADSL technology. With the help of the device presented, it is not possible to connect the Internet using Ethernet technology or fiber cable, as well as create a wireless network. In this article, you will find a step-by-step description of the D-Link DSL-2500U router settings.

Connecting a router to a computer

Before you start setting the options of the router, you need to connect it. To do this, turn on the device into the outlet and run it. Rostelecom cable Connect the router to ADSL connector. Then attach the patchcord, coming from your PC to the LAN port located on the router.

Entrance to the administer of the router

After connection, you must enter the router settings interface using PC. To do this, you need to know the IP address of the router on the network. This information can be found on the sticker glued to the bottom of the router (Adress parameter). In addition, there is an alternative way to find out the address of the device:

  • Click on the network icon on the Windows pane (next to the date and time).
  • Click on the Control Center string.
  • Select "Adapter Settings".
  • By clicking on the current network, select "Properties".
  • Open the "Details" section.
  • The IP address of the router is in the "Gateway" parameter.

Now you can log in to the D-Link DSL-2500 router settings:

  • In the address bar of any Internet browser, enter the found IP address and press ENTER.
  • In the window that opens, enter the login and password, which are also listed on the router sticker. If these data is missing, try entering the "Admin" and "admin" combination.

If the data is entered correctly, you successfully log in in the function of settings.

Connecting Internet connection

For automatic configuration, go to the "Wizard" section. In case you want to set the settings manually, you need to perform the following steps:

  • In the top menu, select the "Home" section.
  • In the Left menu, click on the WAN tab.
  • Click on the "Add" button in the center of the window.
  • In the window that opens, enter the values \u200b\u200bin the VCI and VPI parameters. These data are individual for each region of the country. You can clarify them by contacting the technical support of Rostelecom.
  • Go to the next step using the "Next" button.
  • Select the PPPoE connection type (PPP via Ethernet).
  • Enter your username (PPP username) and network access code (PPP password) that Rostelecom provided you. This data is usually communicated to the Subscriber at the conclusion of the contract.
  • If you are connected to the "Permanent IP address" function, check the box next to the "Use Static IP" string ("Use Static IP") and enter the IP address assigned to you.
  • Put the checkbox in the "Keep Alive" item and click "Next".
  • On the page that opens, check "NAT" and "Firewall".
  • Click "Apply" and complete the Internet configuration using the "FINISH" button.

Setup IPTV.

The D-Link DSL-2500U router has a multicast traffic translating function, so that this device can be used to connect the TV console from Rostelecom. Unfortunately, connect the Miserievisor, and you will not succeed at the same time, because This router has only one LAN port. To set up a router to work with interactive television, follow the instructions:

  • Go to the "WAN" section and click the "Add" button to create a new connection.
  • Enter VCI and VPI values \u200b\u200b(they will differ from the parameters for the IInTernet). They can also be found in technical support Rostelecom.
  • On the "Connection Type" page, select "Briging" ("Bridge Mode").

  • In the "Encapsulation Mode" line ("" encapsulation mode "), select" LLC / SNAP Bridging ".
  • Put the box in front of the "Enable Bridge" parameter.
  • Leave the next page unchanged. Then click "Save & Reboot" ("Save and Restart").
  • After rebooting, enter the "LAN" section in the menu on the left.
  • Activate the "IGMP Snooping" parameter, which is responsible for the operation of the multicast packets used to broadcast IPTV.
  • Once again, restart Rorouter

Setting up a DNS server

If in your contract it is written that you must specify the addresses of DNS servers on your router, then you need to log in to the "DNS" section. In this section, remove the checkbox in the "Enable Automatic Assigned DNS" row. Then in two available lines, enter the addresses specified in the contract.


To complete the router settings and activate all the changes made, restart the device again, after that you can fully use it by destination.

Turn on the modem and restart the computer. With the subsequent launch of Windows will give you a window ...

Turn on the modem and restart the computer. With the subsequent launch of Windows will give you the window: a new device is detected.

Windows will try to determine which modem is connected to your computer. You can specify the type of your modem yourself by choosing it from the list that will be offered to you if you check the box Do not define the type of modem (select from the list). I recommend this checkbox in the event that when you specify the INF file, the list of devices is empty.

If the modem does not detect Windows, then you may have errors in ports.

Follow the instructions of the modem installation program.

After the modem installed go to the "Modems Control Panel". Find the newly installed modem to highlight it with the mouse cursor and click Properties.

In the Maximum Speed \u200b\u200bmenu for modems by 28.8 and 33.6 kbps, select 57600, for modem 56 kbps - 115200, and for ISDN modems - 115200 or higher (high-speed adapters with sequential ports must Also offer 230400 and 460800). If the modem does not respond at this speed, then you need to put the speed a little less. If now the modem does not respond, then either you have a modem without correction / compression, or you did not connect it to the network ... :))

Go to the "Communication Installation" tab and in the "Cancel Call when there is no connection" menu, specify the time in 45 seconds. This time is enough to install the connection.

Close the buffer settings window and go to "Advanced". Here, tick the checkboxes: error handling, at the connection stage, data compression. Data control is hardware. If you have a WIN-modem, then control software.

This is complete to configure the modem.

After the system finally establishes the modem and finish the setting of the parameters required to connect via the telephone line, it will be necessary to make the necessary network settings.

Necessary network installations

Go to the "Control Panel" and click on the "Network" icon. Go to the "Configuration" tab. Then click on the "Add" button and from the component list that appears, select "Network Board".

In the list, select "Microsoft", and among the available components - "Remote Access Controller".

The installation program will contact the Windows distribution disk from which it copies and install the necessary files.

Network board installed. Now click on the "Add" button and select Protocol. In a new window, find "Microsoft" and "TCP / IP" protocol.

The installer will again turn to the Windows distribution disk. When installing TCP / IP, you need to install the necessary protocol parameters. In the Network window that appears, set the cursor to the TCP / IP protocol and click the Properties button. In the "WINS Configuration" tab, select "Enable WINS configuration". In the "DNS configuration" tab, select "Disable DNS configuration". In addition, check the label box "Use this protocol" by default.

Setting up the network and protocols is completed.

If you have an ADSL modem or a USB modem, then it can be installed and connect to the Internet.
Next, we'll figure it out in order, which will be required to connect and how the modem is connected to the computer.

We define what we need a modem

Everyone knows that the Internet contains mountains of information that there is dangerous, a lot of viruses, but when everyone is already communicating in classmates, VKontakte, you enjoy searching and the rest I want to connect to the Internet.
Purchase of the modem is usually only the beginning of solving the problem, as the modem needs to be installed and usually it turns out that there is no network card and it is necessary to buy it or the modem bought together with a new computer, but no one provides such services and needs to be purchased.

The modem is a device for connecting to the Internet on the telephone line.
In the modern world, high-frequency signals are used according to different protocols, for example, 3G, 4G, ADSL2. Many have a problem that it acquires and how to install a modem. Ask your Internet provider that he advises. Find out only supported standards.

The most used modems.
Modems in pure form are now small. Combined solutions are more common with the presence of modem functions.
USB modem looks like this:


This is what the ADSL modem looks like.

It has in front of the signal indicators and buttons of simple actions. Rear - cable for connecting.

Typically, the modem connects to the computer via the USB port or the LAN network port. Separately, the connection goes to the power source (in the outlet). Slitter uses to connect to the phone.

Two connectors can be seen in front. The back of this splitter has a separate third input or cable. It is needed to separate the signals of the phone and the Internet. The speed of the Internet is no more than 8 Mbps.
When choosing a modem, focus on its extended functions. What they are more, the better. Prices for modems are quite optimal, there are different price categories. Especially pay attention to the ability to keep the connection in the case of a short-term failure. You can see for reviews of those who worked with the modem. Take more modern modems, for example, D-Link, it is tightly holding a network than TP-Link.

Separately consider another way - connecting via a Dial UP modem.
This is an old method of using the Internet, when there were no local networks or large providers, and even rich state-level companies could terrify the Internet. This is a Dial-Up protocol. Most often supplied in the form of a board. Older computers did not have a slot for such boards, the external modem was supplied for them, which looked and connected approximately as the current ADSL.

After installation, one incorrect movement led to thousands of accounts for international negotiations. Installation and use of such a modem can be useful in the village where there is no other Internet, or when the main provider has failed in work, and to visit the website Oh as needed. The speed of such an Internet depends on the modem, approximately 56kbit / s.

Installing modem

1. USB modem.
1.1. Let's start with the fact that opening the modem packing, disassemble it and insert the SIM card.

1.2. Connect the modem to the computer's USB port or laptop.

1.3. We wait for the automatic installation of drivers.


1.4. Install the Connection Manager and check the settings.

1.5. Activate the balance, and then press the "Connection" button

2. ADSL modem.
2.1. Connect the modem to a computer or laptop.
The modem connects to the corresponding port, as indicated above: USB or LAN.
Internal modem is connected to PCI slot as any computer board.
Users of the Sandy Prefix Prints will surely cope with the installation, because the installation processes of the cartridge and the internal modem are very similar.

2.2. Next, the cables are connected to the solite or telephone socket with several outputs.
The phone itself is connected to the connectors, the modem cable.
The big minus of the modems installed inside the computer, the ability to burn out the computer due to the large voltage in the telephone network.
Perhaps these are rumors, but after several computers with such modems had breakdowns, I could no longer advise the option with an integrated modem board, but only an external modem.

Setup equipment.
For better management, we put the driver on the modem from the disk. Access to the modem is determined by the network settings and the settings of the modem itself first need a computer to set default addresses.

2.3. We go through the "Start - Pennel Control" - turn on the view by categories - in the "Network and Internet" section find "View network status" - there "Changing the parameter of the adapters" (left column) - we find the desired adapter-right mouse button and "properties". Now we find the Internet 4 protocol (it is TCP / IP 4). We click Properties and set an automatic definition.

If you do not have a step with step-by-step setting, you can go to the modem itself. This is done in the browser input of the address 192.168.1.1.

2.4. You will get something like these settings.




Top and on the side are visible tabs with parameters. Now it remains only to configure the IP address, subnet mask, DNS server.
Information about this data and other auxiliary settings to take the provider.
Settings of various modems are different. In extreme cases, read the manual. This is exactly the way the modems were set up with us. It remains only in the tray right-click on the icon and select Connect.

3. To configure the Dial Up We reveal before viewing the network status (see the instruction above), then at the bottom of the window press the configuration of the new connection.
3.1. In a new window, select the configuration of the telephone connection, click Next, then enter the number, username and password. This data is taken in the telephone company.
3.2. Now it remains to go to network connections (see Instructions for Settings Changing the Adapter Settings), we find the desired adapter (it will be the connection, it will be written on the telephone line), click on the right mouse button, connect, OK.


The picture remains to connect the cable and click Connect.

Operation and possible malfunctions

After connection, you can safely use the Internet. If there is no Internet, check the settings. There are impossible to give specific tips here, since how many providers, so many individual settings, have many ways to install a modem. In extreme cases, call the wizard and remember everything he did. If the cause of the absence of the Internet is the line failures, then restart the modem. When using the Dial Up, watch all actions, control traffic, do not attend dubious sites.

Modems may have faults that allow you to connect to the network and load information and many users are surprised - the Internet light burns in red all the time, and the download goes.
There are malfunctions from the provider - when the light burns red and no connection. You can check interviewing familiar or neighbors - whether the Internet works from them, call the support service, connect the familiar mode.
I hope that all your problems conclude that you did not know how to install a modem or just need to wait, conclude an agreement for the provision of services.

In Russia, the Internet appeared relatively recently, but now it is possible to say with confidence, it enjoys the entire population of a multinational country. In order to work with this network, you will have to purchase a special device that will allow you to freely go out into the global "space". At the moment, the most famous technology has become ADSL. It allows you to use the telephone line at the same time both for calls and for the Internet itself. How is this division? Due to the splitter. It is available in any modem running on this technology. Before each user of the network, at least once, but the question was: how to choose the necessary device and not guess? Providers and manufacturers of equipment offer completely different modems. From the simplest to tricky capable of creating a wireless network. The article discusses the most successful ADSL modems.

Acorp Sprinter W510N.

Most recently, this model has appeared on the market. She received the functions of the router, switch. Moreover, the device is capable of working with a wireless network. Like many other ADSL modems described on a powerful built-in RealTek processor. The device received good characteristics, and the manufacturer noted that this model has an improved speed of operation and the function of saving electricity. The device received up to 32 MB of internal memory. This item is quite important, because it is at the expense of her that he will either work under load or not. The modem can provide maximum Internet speed up to 150 Mbps per second. This is a normal indicator, so consumers celebrate this device as one of the good.

The model is universal, it has some functions from the router. Moreover, the device is capable of working offline. When creating a large local network, you can quickly split the Internet with this modem.

TP-LINK TD-W8961ND

The following model is a TP-LINK ADSL modem. She has long been in demand among advanced buyers. This is due to the fact that the device combines three types of similar devices. The model has many ports, capable of working with a wireless access point. The router functions on a modern standard, and it is able to show excellent performance at high network speeds. The maximum incoming traffic indicator may be equal to 24 Mbps per second. If desired, using this device is always allowed to create a network and use both wired connection and wireless. The maximum data transfer rate was 300 Mbps per second. On the device you can see two removable antennas. It is they who provide a high level of signal, capable of holding it if it is bad. The connection itself is quite "clean" and never interrupted.

TP-LINKTD-W8961ND router features

This ADSL modem is a wifi router. Therefore, has an additional functionality. It is also perfect for working with television, since the speed of the network at the maximum level. It is stable until malfunctions from the provider appear, in other cases - the maximum. Judging by consumer reviews, this model of the device does not show work with ruptures and failures, so it is in demand. Included with the device comes with a cable for connecting to a computer. Some are even wondering how to configure an ADSL modem. Do not necessarily do it yourself. It will be enough or contact the service center, or invite an assistant to the house.

The device uses special firewalls. The signal that passes through the modem is strengthened, becomes protected and it helps to prevent hacker attacks.

Zyxel P660RT3 modem

Another famous router. It is easily connected to an existing local network and immediately starts working. The device has many functions, among which there are both the options of the router. It is capable of working with any type of technology through the cable. But at the same time connect directly to several external devices will not work, as the port is only one. However, you can easily "distribute" the Internet to all members of this local network. This is how much easier to serve the available computers.

Not all ADSL Internet modems work with an emphasis on the domestic user, we are talking about the same device. It has reliable encryption of the signal, standard and connections. This will save a person from hacking his computer. Otherwise, the consequences can be quite terrible. Communication is good, without failures. Problems do not arise, even if some kind of interruption happened on the line. Communication operates at high speed. The maximum load indicator of this modem is a limit: no more than 24 Mbps per second. The device comes with an external charging unit, indicators on the router itself. With this firmware, which is on the device, you can easily apply IP telephony. It is much more convenient and cheaper.

Trendnet TEW-635BRM

This ADSL modem is a router, which is equipped with a large set of functions. He is able to work immediately in two modes. It is quite convenient and allows you to use a large number of options. The switch is designed for four ports. Due to this quantity, you can simultaneously connect a laptop, computer and other technique.

The modem of this model is also able to work with the Wireless Internet Access Point. As for the appearance, the device looks good and attracts consumers. Available maximum speed of the Internet is 300 Mbps per second. This result is achieved through the use of three antennas and modern functioning technologies. The housing is located a shutdown button and turn on the wireless network, which is quite convenient.

D-Link DSL-2520U

Not all ADSL modems are suitable for huge offices and premises. It is about such a thing that will be discussed. The DSL-2520U router is recommended for use at home. This model works with two ports: one is responsible for transmitting data for computer networks, and the second is USB. This device positions itself as a fairly convenient, which will allow you to create an access point quickly and in a few minutes. The device is equipped with a special function that gives you the ability to transmit a better signal, as well as it has a built-in screen. To manage and configure the ADSL device (D-Link modem), you can always go to web settings. They are most clearly understood, so it is unlikely to understand anyone with them. If any problems arise, you can always take advantage of either a certificate on the Internet from the official site, or take a special book that comes in the kit.

Linksys lapn600.

This model is known for the option to redirection of protocols. According to consumers, the device is quite easy to configure the device. The speed of the wireless Internet is 300 Mbps per second. The ADSL model (WiFi LapN600 modem) supports work with many standard modes. The device can be heated to a temperature of no more than 35 ° C. In general, it does not affect the work and functionality, therefore, it is impossible to consider something negative. The modem is able to interact with many well-known network modes.

Cisco SB WAP188.

The router works with a built-in antenna, so changing it, if necessary, will not work. The modem has a special receiver that enhances the signal and allows it to make it better. According to consumers, the configuration of the ADSL modem occurs quite easily.

Internet frequency - no more than 2.3 GHz. The model can operate in several network modes. The Internet applies to 210 meters, but not more. The device works stably at a positive temperature and at no less than -10 ° C. The user can view all the texts of the configurations, as well as allowed to make changes to them. The weight of the device is 310. Sale for 6 thousand rubles. You can not configure via the command line.

ASUS EA-N66

How is the configuration of the ADSL modem? This is quite easy to do, but it is necessary to explain on the example of one of these devices. You can do this through a special VAN port. Find it easily on the back of the device. It is clearly distinguished on the rest of the rest, as painted in blue. After the cable is connected, you must go to the browser and make all the settings there. If there are any special requirements, then you need to contact your provider. The router itself is sold with the priority option. When setting up different channels do not have to spend a lot of time. Immediately when implementing all changes, you need to pay attention - whether the software update came out? If so, you immediately install it.

The device also works as a repeater. Antenna This device has a removable type, so, if necessary, you can use more powerful details. The Internet router spreads to 240 meters. The router itself has a special protection against viruses. She is quite high-quality, there are no complaints from the user. If you wish, you can manually view the configuration and change them. The model costs about 5-6 thousand rubles. Forwarding options are not here.

ASUS EA-AC22

This ADSL modem is a wifi router. Many buyers choose this type of equipment only because it is capable of maximum wireless speed. That is, you need to immediately say that in this model he is at a high level. The router works freely with many network modes. Embedded antennas. The device weighs a bit, a little more than 300 g. It is quite easy to control the device. Customize too, as the web interface is as defined and convenient. Update the described modem, like many others, will not work.

If we talk about the security of data and connections, then you need to say - here it is at the highest level. Moreover, even a filter is embedded.

RESULTS

Now the devices that are considered universal are becoming increasingly popular. Not all ADSL modem can work with a wireless access point. However, those that received this function show only its stable functionality, no complaints about it. The connection passes through a wired and wireless channel.

Similar articles