If you have and you want to see what the developers have studied, despite the fact that you can easily lose the right to warranty service - this instruction will help you at least not to cause significant harm to your device.

So, in order to disassemble the smartphone, the first thing you should unscrew the two PENTALOBE screws located on the lower end of the device. Due to its non-standard and related difficulties, Epplovsky screws earned a lot of obscene epithets in the blogosphere.

After you overcome this difficult barrier, you can assume that half of the work is made. To remove the lid-screen, it is desirable to use some non-leaving traces of the tape or suction cup.

It will not completely remove the lid due to the display of the display located in the upper part of the smartphone, but it is easy to disconnect it with a thin plastic plate (for example, a mediator).

Further, inspected "Stuffing" iPhone It can be noted that all other parts are screwed with standard screws. Therefore, you will not be difficult to unscrew the metal plate that holds the front panel.
After that, it is necessary to remove the HOME button to be removed. Cover parsing Complete the loop shutting down and dismantle the dynamics and front camera.

Next, with the help of a plastic plate (to which the display loop disconnected), remove the battery. Tweezers remove the rear chamber and antennas. Then remove the protection against electromagnetic pulses.



Finally, it remains to dismantle only the vibromotor, the charging connector, the microphone and the on-line buttons and adjust the volume. Manipulations should also be carried out by tweezers.




Summing up, we can notice that it is not so difficult to disassemble yourself. In particular, in contrast to the previous model there is no difficulty with a loop of a dactyloscopic sensor.

In this step-by-step instruction on the analysis of the iPhone 6 Plus, you can clearly see how to fully disassemble this smartphone, thereby be able to replace the screen, motherboard, buttons, speakers, battery and other IPhone 6 Plus elements.
As always, you need to start with the screws that are located at the bottom of your iPhone 6 Plus.

Now you need to disconnect the screen from the phone itself. For this, a professional ISCLACK tool will be very convenient. Without it, it will be difficult, it will be necessary to work with plastic blades for quite a long time. Immediately unscrew the loops that go to the iPhone 6 Plus screen.

We see the inside of the phone, you can see how much the battery on the iPhone 6 Plus has become more.

Remove the plate sewn from the "Home" button, after which we remove the button easily and the itself.

We remove the front camera, in which the speaker also works for the conversation.

With the smartphone panel of the iPhone 6 Plus, remove the metal plate.

We remove the battery cable and pull it out of the phone body.

We remove the vibrator block assembly.

It was a turn to dismantle the camera, it is easy to make a thin tweezers, the main thing is not to damage the contacts, for this be careful.

We gradually approach the final of our disassembly. We unscrew the attachments of the motherboard, after which we remove the attachment of the antenna.

In this manual for disassembling iPhone 6 Plus, we will not describe the details that are on the motherboard. A new article on this topic will soon appear on our blog, you can find out detailed information about the iPhone 6 Plus motherboard schema.
So far, we continue to disassemble the smartphone, the speaker queue:

If you are interested in the theme of the iPhone repair at home, you must remember what you do to your risk. Not only is your phone after disassembly outside the Apple service center loses its warranty - you can accidentally damage or incorrectly mount one of the gadget nodes. Finally, Apple devices are quite difficult to disassemble independently, manufacturers suggest that you will serve them only in branded centers.

If you did not scare this caution, and you are firmly sure that you want to know how to disassemble the iPhone at home - moving on.

In this text we will look at how to disassemble the iPhone 4S, 5, 6.

We disassemble the iPhone 4S

To start, make a backup copy of the iPhone, because you may need to restore it after assembly. Make a copy will help iTunes. Be sure to remember the order of disassembling the parts of the device, and better - lay out the details of the phone strictly in the order that was disassembered and each step - take pictures. Pay special attention to the screws of different sizes - they should also be left in understandable for you, so as not to get confused when assembling.

• First of all, remove the SIM card slot from the machine and the card itself too. To do this, you will need the original clip from the iPhone set, but if you do not have it - the usual stationery is suitable.
• From both sides of the charging connector there are screws - unscrew them.

  
  

• The lid hiding the battery needs to move up and disconnect it. To the left of the battery, in the corner there is a small protective plate that hides access to it. Remove these two screws.

  
  

• Now you can see the connector suitable for the battery. It must be accurately removed. Remove the battery by pulling the small plastic tongue.

  
  

• In the upper left corner you see a S-shaped protective plate, it keeps on 5 round screws. Unscrew them.

  
  

• The protective plate hides underly six loops, they all need to be disconnected. In no case do not go to them and do not squeeze the loopholes too much!

  
  

• Five plumes are located on the surface and are completely noticeable, but the sixth is blocked and will be available after the removal of these five. Disconnecting the extreme left loop allows you to remove the camera's camera. At the same stage of disassembly, you will be available to the screw in the upper right corner, unscrew it.




• When you remove the camera's camera, unscrew the three more screws. Two of them are located one over the other, under the plastic tongue (we used to remove the battery), and the third left, aside. If you connect these screws imaginary lines, it turns out - ⅃.




• Now you come to remove the battery loop, it is relatively large, but to remove it will be enough to raise it up.

  
  

• Below, the next screw is located on the right to be removed. It is located at the very edge of the phone body. Now go to the disconnection of the replay of the antenna located on the left. Its type differs from previous connectors, but it is connected in a similar way. This loop must be carefully lifted. After that, the antenna and call block at the bottom of the iPhone will be disconnected without an additional effort. This is a black, stretched out the detail.

  
  

• Taking the orange cable towards the orange, you will see another screw.
• Unscrew two pairs of screws. The first pair at the bottom. Here, one screw was under an orange loop, and the second is slightly higher, on the right.
• The second pair of screws is located in the upper part of the iphone case. The first is next to the camera slot, in the upper right corner of the slot. The second is on the same level, on 3 centimeters to the right.

  
  

• Thus, we freed the motherboard of the apparatus and can dismantle it. Motherboard - a single block with diagrams passes through the entire body of the phone. Next to the orange loop is a sucked part and it will also be necessary to remove it. Note that it is planted for bilateral scotch, so it will take some effort to disconnect. Do not overdo it!




• In the next step, you must remove the entire 10 screws holding the iPhone 4S module. Four of them are located in the corners, and the rest - on the right and left edges of the iphone framework. Note that 6 side screws have a different size, and the fears are located behind.

  
  

• After this operation, there is still some number of screws, but at this stage it is not necessary to disconnect them.
• We carry out a specially prepared tool (mediator, plastic blade) along the screen so that it is disconnected.

  
  

• To replace the display module with a touchscreen, the description is sufficient.

  
  

• To replace the "Home" button iPhone 4S, shift the black valve to the right. If you want to remove the iPhone 4S button, slide the black valve to the right. It is above the charging connector. By the way, you need to remove it, for this you have to unscrew two round screws. Now it is possible to remove a long orange loop.

  
  

• The remaining connectors, including the loop from the phone start button (located on top) and the volume button buttons are disconnected if you unscrew the latest screws.

This video visually shows how to fully disassemble the iPhone 4 and replace the screen.

We disassemble the iPhone 5.

• First of all, we unscrew the rear cover of the device and remove the screen.

  
  

• To do this, you need to unscrew a couple of small screws on different sides of the connector for charging the device. It's not difficult to find them.

  
  

• Next, using a vacuum suction cup by removing the screen. You can perform the operation with a small plastic blade or mediator. In this case, the screen is needed to hook from below, and then lift. Performing action, you need to be as careful as possible not to split and not scratch the display.

  
  

• Even the iPhone 5 often meets a problem with easily erasing paint. Viewing the phone, you need to remember this at every stage of work.

  
  

• After lifting the display, disconnect it from the main block of the diabel. Note that the nodes of the device are quite firmly connected.
• After unscrewing the last bolt on the board, gently lift the screen cable. Here you will need a mediator or plastic blade. Now the screen can be completely removed.

  
  

• We dismantle the battery
• In no case do not let this step of disassembly, because further steps with a connected battery can end the current blows. It is not only dangerous for you, but also causes defects of other nodes of the phone.
• 
  First of all, you need to unscrew three screws holding protection on the battery loop

  

• To remove the battery, use the same plastic blade. The battery may not succumb to you from the first time, but it's not worth worrying because of this. Carefully use it from different sides until the glue that holds the battery is not separated.

  
  

• We take out with the IPhone 5 motherboard
• After driving the battery, unscrew the bolts on which the camera holds. There are two of them. After that, we successively turn off the microphone connectors, dynamics and headphones. After the screws are followed, the antenna loop and the SIM card slot are attached.

  
  

• When you unscrew the 5 of these screws and disconnect the plumes, slowly remove the motherboard.

  
  

• At this stage of the disassembly of the device, the iPhone 5 case can be postponed, because further manipulations occur directly with the motherboard. Remove the camera, unscrewing two screws. No additional elements of fasteners do not have this node and then freely disconnects.

  
  

• We turn to the vibromotor attached to three screws. Then, to remove the bottom loop of the motherboard. To completely remove the lower loop on the motherboard, which holds the port Lightning, Jack for the headset, speaker, Wi-Fi antenna and one of the microphones, you need to unscrew the seven seven screws: two at the bottom next to the headphone jack, one in The right side of the loop and four more, directly holding the entire component.

  
  
  

• Remove the CPU
• To separate the iPhone 5 processor, you first need to remove the protective film from it.

  
  

• Remove the details from the front panel.
• When you separated the remaining items from the back of the apparatus, you can go to the front.
• The "Home" button is held on the glue, the button must be accurately pushed and remove

  
  

• One of the last elements to be disconnected is a metal plate that protects the screen from contacts to other hardware parts of the device. After the last detail is removed, the disassembly of the iPhone 5 can be considered complete.

In this video you will learn more clearly how to disassemble the iPhone 5

Disassembling iPhone 6.

Joyful news: iPhone 6 is easier to collect and disassemble compared to predecessors. This is undoubtedly due to the fact that the device has become thinner, but more. Thanks to these changes, access to the details has become easier, they are placed in a more spacious case.

More details of the disassembly of the iPhone 6 you can view in this video

I would like to add a few words about special tools that will be required to disassemble Apple smartphones.

As we have already found out, we can not do without:

1. Sucker
2. Plastic mediator or special blade
3. Tweezers
4. Set of special screwdrivers

It is on screwdrivers that I want to stop in more detail, let's look at what characteristics and designs they must have the disassembly of the iPhone to go without bitch and zadorne.

As an example of an optimal set of screwdrivers for the repair of electronics, we suggest considering the production of Vira.

First of all, the holder. It is made of shockproof plastic and for the convenience of grip has a rubber coating. The holder is 11 cm long, it is possible to bite the whole palm, while it is not too long.

Traditionally, for such holders, it is considered important for the presence of a rotating site. You can put pressure on the tool, while the housing will easily rotate with your fingers.

Includes 28 bits:

• 25 mm SL1.5,
• SL2.0, SL3.0.
• PH000, PH00, PH0, PH1
• T4, T5, T6, T7, T8, T10, T15, T20
• H2.0, H4.0.
• PZ1, PZ0.
• ★0.8, 1.2, 1.5, 2.0
• ▲, 2.0, 2.3
• Y 2.0mm, ∪2.6mm

Listed Types of the bit easily allow to repair any apple knot, including the "Pentalobe" slot.

Special attention should be paid to the material of the bit and their additional processing. The material is used with high hardness so that the tips do not get erased over time, or erasing less.

The bits of the VIRA kit are made from chromium vanadium, solid and durable material.

Because the disassembly of the iPhone is a constant work with small details and fixed-size fasteners, it is better that the bits had a magnetic tip. So fasteners it is easier to picked up, put into the hole in the housing of the smartphone.

Special attention is paid to the placement of the package in the package. Each bit is its own cell, they are fixed motionless and not mixed when carrying a set. The bundle of the kit is made of high-quality solid plastic, which is able to withstand the fall on the floor from the height of human growth.

For additional convenience of storage, the box has a back sliding tap. Due to this, the kit can be suspended on the wall.