ACORP has long been the leader in the supply of OEM devices to operators and providers in Russia. Wireless routers This company, in our market are represented by two 100 megabit models: it is WR300N, and WR150N (from the first - differs only speed Wi-Fi). We will consider the "senior" model WR300N. In fact, the WR-N series routers are endowed with all necessary to create. home network Functions, and only the setting of the ACORP router may seem somewhat "unusual" (perhaps, this is the main, and the only drawback). Consider more.
Setup is carried out via the Web interface. Connect the router by patch cord (in a set with the device) to the PC network card. At the same time, any port is used except WAN. Then, turn on the power of the router.
PC network card, before setting, should be in the "automatic" IP address and DNS mode:
For this, you configure the properties of the local connection (as in Fig. Above).
Setting up Router Akorp
Check the PC card, as described above. After turning on the power of the router, you need to wait 2-3 minutes. Then, open any browser. In the address bar - you dial: 192.168.1.1
You will be asked to enter Login and password (suitable Admin and Admin). Any acorp router, modem, that is, everything that has a web interface - allows such a password input.
Connection with Internet connection (DHCP protocol)
Go to the first tab (Operation Mode):
Check that the AP-Gateway is selected (that is, the "router" mode). If not, we select, press "Apply". Go to "Internet settings" (WAN Setup tab):
Configure, as in the figure (Type - DHCP, MTU - Auto, Enable Nat - Yes). Click "Apply". Now, connection with your provider is created automatically.
To save all settings, you go to the "Administration" -dency, on last tab ("Save and Reboot"):
If this step is to skip, upon subsequent download, the router we made the settings - "forget". On this, the router configure the connection "DHCP" - complete.
Setting up connection to the Internet (PPPoE with a dynamic address)
Perform everything that is mentioned above (except for the last step to save the settings). Then, go to the "VPN SETUP" tab (located in "Internet Settings"):
Inside the first (top) block, basic connection information is made (username, password). Do not forget in the first line, select "Client PPPOE", in the second - WAN port.
Lower block - adjust both in the figure (all checkboxes are "incl." Except the first two). On this - the setting is completed. Click "Apply and Connect".
Do not forget when leaving the interface made here Settings - Save ("Administration", last tab).
Note: Setting "Under PPPOE + Static IP" - runs similarly, only on the WAN Setup tab, you select the "static" IP mode (and specify the IP address).
How to configure the ACORP router to connect with your provider - we completely reviewed.
Cloning Address MAC.
If you intend to change the hardware MAC address, "visible" on the "WAN" port, you need to perform several actions.
Section Administration
Go to the "Administration" section, then to the System Commands tab. Text of commands (that is, executable code) will be as follows:
- nVRAM_SET 2860 CHECKMAC NO
- # This is in the first line, and then:
- nVRAM_SET 2860 WAN_MAC_ADDR 00: AA: BB: CC: DD: EE
- # instead of 00: aa ..., Substitute "Your" Mac
- Click "Apply". Save the settings.
Universal WiFi Router ACORP WR300N includes an access point operating in 2x2 mode (2 antennas and 2 transmitters, up to 300Mbps). Wi-Fi Setup - Absolutely "standard" (executed on one tab), and the choice of transmitter power (provided here) can be very useful.
We go to the tab "Basic", section "Wireless Settings". First tick - put in "Enabled" (i.e. - "Enable" Wi-Fi Network):
Come up with your network name (SSID). Set the mode (B / G or N, better - "Mixed"). Maximum connection speed, achievable in "N-only". The rest - you can leave the default. Click "Apply".
Operating Mode mode -\u003e "Greenfield" can be used only if nearby - there are no other access points (or - there is, but they are also included "Greenfield").
Click the Advanced tab.
Here, the necessary "power" (as a percentage of maximum) is selected. Set the value, click "Apply".
Setting up the WiFi ACORP router to work "without encryption" network, on this - completed. Enable encryption (set the key and select mode) - can then be on the "Security" tab:
Before leaving the interface, save the settings (turning to the "Save and Reboot" tab, in the Administration section).
Optional: View IP-TV in a wireless network
There is a problem: as soon as they include an IP-TV player on one of the PCs in local network, other devices - work slower. Each Router Akorp (300N, 300NU and 150N) - solves this problem in the following way: IP-TV Package Traffic, you can reduce artificially.
We go to the "Advanced" tab, in the "Wireless Settings" section. In the bottom block, we see:
Here, you need to choose "Multicast TX RATE". Meaning - it is better to put on "half" (or - "two thirds") from average values bandwidth wi-Fi connections. Click "Apply". Save the settings.
Note: In the case of "0", "multicast" traffic - no fully (watch IP-TV via Wi-Fi is not possible).
- For video "720p" - 2 megabit / s or more;
- For Full-HD video - 6-7 megabits / s.
Basic adjustment router
Setting up ACORP SPRINTER W422G modem in router mode
Turn on the modem into the 220V socket, connect the phone cord from the DSL connector on the Acorp Sprinter W422G to the ADSL connector on the splitter.
After some time, it should freeze and then light up the ADSL indicator to the smooth light. If the ADSL indicator on the ACORP SPRINTER W422G modem does not light up, which can be done in this case.
Press (for example, with a rod from the handle) and hold the resetting "reset" button on the rear wall of the ACORP SPRINTER W422G modem. Wait until the display changes on the modem, then release the button. This will reset the ACORP SPRINTER W422G modem to the default factory settings.
Turn the network card to mode.
Note for lovers to search for drivers to all new devices: Driver for ADSL modem ACORP SPRINTER W422G is not required, because This is a completely independent device connected to the network card. Drivers may be needed for modems connected to uSB portAnd the ACORP SPRINTER W422G does not have USB support.
To start configuring the ACORP SPRINTER W422G modem, type in the address bar of your Internet browser 192.168.1.1 and press the Enter key
A window appears with a password request. Dial Admin Username and Admin Password
Click the "Log In" button.
If all right, then after entering the password, you will see the following window: 
The easiest way is to configure ADSL ACORP SPRINTER W422G modem via Wizard. Click the Wizard button in the top menu and this window appears on the screen: 
1. Select the connection type in the Protocol field. Usually users prefer to configure ADSL modems in router mode. In this mode, the ACORP SPRINTER W422G ADSL modem will automatically serve computers connected to it, and to access the Internet with new computers, it will not be necessary to change anything in the ACORP SPRINTER W422G modem settings. Select PPPoE to configure in router mode.
2. Enter the VPI and VCI parameters to be provided by your provider.
3. Enter the username and password. They must also be provided by the provider.
4. Click the "Next" button.
On the page that opens, click the "Save / Restart" button. After clicking on this button, in no case, do not turn off the ADSL of the ACORP SPRINTER W422G modem, because It will save the entered parameters and reboot. After rebooting an ADSL modem, you must have the Internet;)
For amateurs, to focus with more advanced ADSL modem settings, such as package filters, portsing ports, dynamic DNS, WiFi and QoS encryption There is an ACORP user manual. User Guide For ADSL modem ACORP SPRINTER W422G can be downloaded.
ACORP SPRINTER W422G modem firmware
ACORP is constantly working on improving the ACORP SPRINTER W422G modem firmware. In each new version, minor errors are removed in the modem, and the most important thing is to optimize and accelerate the operation of the ADSL modem. Therefore, the ACORP SPRINTER W422G modem firmware is recommended to all advanced Internet users.
Download file S. new version ACORP SPRINTER W422G firmware is best on the manufacturer's website. Choose a version for Annex A / B, because Apparently, the ACORP programmers are actively working on this version.
After you downloaded a file with the firmware ADSL modem Akorp Sprinter W422G and unpacked it from the archive, in the ADSL modem settings, go to the Tools item -\u003e Update Gateway.
To update the router software, select the update file (kernel / file system) or configuration file (SELECT A File), and then click the "Update Gateway" button.
If you wish, here you can unload the existing ADMS modem configuration of the SPRINTER W422G modem, by clicking the "Get Configuration" button.
IP 144.76.78.4 Browser SEARCH BOT SYSTEM Country Provider
Setting up acorp W422G.
ADSL router with access point and 4-port Ethernet 10/100 Base-T switch
Instructions for setting megaline for the ACORP W422G router. This statement provides an example of configuring the device through Web interface, installation of drivers and other software The computer does not need. You will need only the Internet Observer. Will suit any - Google Chrome., Opera or Mozilla Firefox
Before configuring the connection, reset the device settings to factory settings. On the rear panel there is the "Reset" button Press and hold it within 5-7 seconds until the indicators on the front panel are blinking at the same time.
Connect the device to the computer using network cable. In the browser's address bar, enter the address 192.168.1.1. Specify the username - UserName. and password - Password. To access the device settings. Factory Login and Password Admin. - With a capital letter! If you cannot enter the web interface, check the settings network connection, In the properties of the network connection for the TCP / IP protocol, the IP addresses and addresses DNS servers Must be exhibited - get automatically.
To configure the connection settings, go to the tab Setup\u003e New Connection Set the following parameters as shown in the screenshot:
Name. - the name of the new connection; This is a mandatory parameter, but its value may be arbitrary and does not affect the connection.
Type - Connection type: PPPoE;
PVC settings - the parameters of the virtual channel;
For users Megaline: VPI - 0; VCI - 40;
UserName. and Password. - username and password issued by the provider.
Then you need to apply the settings. Apply And after a few seconds the device will connect to the Internet. For users Megaline:
If you do not remember your password, or you can not connect with your password you have, use the guest accounting. Drink in the username field the word "megaline", in the Password field also "Megaline" (all letters Latin in the lower case, and the VPI / VCI values \u200b\u200bcan be any). So, you will not be able to enter the Internet, but you can get into personal Area And set a new password on the Internet.
By default, access to the device settings is possible only from the local network, so you can leave the factory login and password Admin..
If you consider it necessary to change the factory login and password it can be done in the tab Tools\u003e User Management.
At the end apply the settings Apply.
The device is equipped with a wireless access point, IEEE 802.11 G standard
To configure the main parameters wireless network Go to the tab Wireless\u003e setup..
Pay attention to the following parameters:
Enable AP. - enable wireless network support; The default is on.
Primary ssid - the name of the wireless network; Name you will see in the list network available When connected. You can leave the factory value.
Hidden Ssid. - hide the name of the wireless network; Additional precautionary measure is not a serious wireless protection tool. The default is turned off.
User Isolation - Limit access to the resources of the local network is allowed only to access the Internet.
Apply Settings Apply.
Setting the wireless network settings
To configure the security settings of the wireless network, go to the tab. Wireless\u003e Security.
Select Encryption Method WPA2. If you want to ensure the maximum level of protection;
As a login mode, select Pre-Shared Key - security key;
Specify the key combination - Psk String, not less than 8 and no more than 63 characters;
Apply settings upon completion Apply.
Saving configuration settings
An article on setting up an ACORP router W422G and WAP-G models.
The instruction is given by the example of the ACORP router from the Rostelecom campaign, but it is also suitable for other models and firmware.
Routher Connection Scheme
On the back side of the router W422G or WAP-G there are several ports.
If now computers will be connected to it using the LAN cable, there are 4 connector here.
The fifth port, located separately from the four others, is designed to connect the Internet cable (the one that held employees Rostelecom or Megaline from the entrance). If your computer has no wi-Fi antennasInsert the cord that was in the box, on the one hand to the device, and on the other - in a similar entry network card On the rear panel of the system unit.
Configure the connection of the router to the Internet
After that, turn on the ACORP W422G or WAP-G router, and open any browser on the computer - the program for browsing the Internet.
In the address bar, dial 192.168.1.254 or 192.168.1.1 and click "Enter".
We emphasize, not in the search string, namely in the address.
Usually, by default, these are the words "Admin" and "Admin".
Here is produced full setting Router. To do this, click on the "SETUP" tab and then click "New Connection". Next, fill in all fields that appeared correctly:
- Name - connection name (any);
- Type - Connection Type (PPPOE);
- UserName - username (provided by the Internet service provider);
- Password - password (provided by the Internet service provider);
If everything is done correctly, we save the changes - click on "Apply" and wait for the connection of the modem to the Internet, then check its operation with any browser. For a computer, the router serves as a modem.
Setting the WiFi Access Point on the Router
The Wi-Fi setting is made on the "Wireless" tab. On the left, select "SERUP". Check "Enable AP" - must be included. Next, go to "Security" and select WPA2 encryption method, and enter the combination of at least 8 characters in the PSK String field (this code will be needed to connect wireless WiFi. Modem network).
