Honestly, until this pore was not familiar with Netis routers. I bought the Netis WF2411 model to see what kind of devices, well, and prepare several instructions for setting up these routers to the site. And in this article I will tell you how to enter the Netis router settings. There is nothing difficult there, but I have seen such questions several times, so I decided to prepare a small instruction, how to get into the Netis control panel. As you already understood, I will show on the example of Netis WF2411. But if you have another model, then the process itself should not be different.

After logging in to the settings, you can configure the Internet, Wi-Fi network, set, or change the password, etc. By the way, at all these moments I plan to prepare detailed instructionswho think many will come in handy. Compared to other routers, Netis itself does not differ in the settings page at all, so if you already have experience, there should be no difficulties.

Open the Netis router settings at 192.168.1.1

To begin with, we need to connect to the router. If you want to go to the control panel from a computer, or a laptop, you can connect to the router using a power cable that comes in the kit. On the router cable connect to the LAN connector, and on the computer to the network card.

Can be connected and go to settings Wi-Fi network . Just connect to the wireless network of your router. If a new router, or you just made a reset of settings, then the standard name Wi-Fi network will be approximately: "Netis_C2323B" (Standard name (SSID) is indicated on the sticker of the router below). Password to Wi-Fi by default, I had "Password". This information is also specified on the sticker from the bottom of the device. Also there is the address to access the Netis router settings.

Just connect to this wireless network From your laptop, or a mobile device.

We go to the settings through the browser

If after connecting to the Netis router, you saw a yellow icon near the Internet connection icon, and the status "without access to the Internet", then it is quite normal. Just the router is not yet configured, but I don't need to enter the Internet settings.

After connecting, open any browser, and in the address bar type the address 192.168.1.1 , http://netis.cc., or 192.168.1.245 (on new models). As you can see in the screenshot above, the address 192.168.1.1 is not specified on the routre, but only http://netis.cc. But on it, the settings are open without problems. Dial, or copy the address and go through it. New devices are indicated IP address 192.168.1.245.

Immediately open a quick setup page.

You can change the language of the settings into Russian. And what to open more settings, just click on the button Advanced.

This is how advanced settings look like:

I really liked the control panel itself. Simple, nothing superfluous, there is a Russian language (TP-Link, hello), and a great page with the rapid and most important settings, on which you can configure your Netis, you can practically in a few clicks with the mouse. And if you need, you can go to the extended settings, and also quickly return to the rapid settings.

netis.cc or192.168.1.245 and login / password Guest

Update: On the new Netis router models, the web interface (page with settings) is already protected by login and password. Login (User Name) - guestand password (Web Password) - [Email Protected] . Where XXXX The last four symbols of the router MAC address.

The request to enter a user name and password will appear in the browser, after switching to http://netis.cc or 192.168.1.245.

The IP address itself has also changed. It is already used http://192.168.1.245. Either an old hostite http://netis.cc.

The web interface itself has also changed a little.

In terms of security, this is a good solution. I mean the installation of the Guest login and the password on the factory settings. In addition, the password on each router will be different, since the MAC address for each router is unique. Previously, the default settings for Netis routers were not protected at all. And few in the process of setting the router installed this password (although I write about it in each instruction). And if the settings are not password protected, anyone who is connected to the router can access the web interface.

But on the other hand, the process of setting up the router is a little more complicated. You need not just to connect everything and dial the router address in the browser, and also enter the username and password. According to my observations, it causes difficulties from ordinary users.

What if it does not enter Netis settings?

It may also be that when trying to open address 192.168.1.1, 192.168.1.245 or http://netis.cc, you will see a message that "Pages are not available", or "Unable to open the page." Several Soviets by decision:

• First of all, look at the tips from the article, which is written specifically on this issue:
• Be sure to check if you have an automatic receipt of the IP address in the connection properties. How to do this, I described in detail in the article, the link to which is higher.
• Check if the power is turned on by your router.
• Check the cable connection. It may be that you mistakenly connected the cable not in the LAN connector, but in WAN.
• If it fails to go to the settings of the Netis router over the cable, then try on Wi-Fi. And vice versa.
• Try to open a web interface from another computer if there is such an opportunity.
• Make a reset of the router settings, and try moving at http://netis.cc again.

That's all. I hope you all happened. Good luck!

1. Connect the power cable to the router and turn it on into the outlet. Internet cable, installed in the apartment, connect to the WAN jack on the router.

2. Connect the network cable, which is included with the router, one end to any LAN jack of the router, and connect the second end to network card Computer.

If you want to configure the Wi-Fi router, then connect to the wireless network, which will appear after turning on the router. It may be called "Netis_A508B3", a password may be required to connect to the network. Network name and password are indicated on the back of the router.

3. If the computer has been connected via the cable, then you must enable automatic receipt of the IP address settings and DNS servers, this will help you.

4. Open any browser. In the address bar, specify the IP address of the router http://192.168.1.1 or http://netis.cc and press ENTER or "Go". A page with the router settings opens.

5. Select Russian Language Languages

6. In the "Connection Type" menu, select item " Static IP "and introducesettings issued to you when connected.

7. To configure the Wi-Fi network in the "SSID" field, specify English letters any name for your network, for example login, "Security" Install on. And set a password to connect (minimum 8 characters).

9. In case IPTV is used, you will need to open extended settings: click "Advanced"

On the left, click "Extended" - "IGMP", "Status" Select On. and click "Save"

To configure the prefix in STB mode, on the left, select "Network" - "IPTV", "IPTV mode" specify the bridge, "IPTV port" - LAN1 and click "Save"

Then connect the console to the LAN1 jack on the router and in network settings consoles Specify the parameters issued to you when connecting IPTV

The topic of today's article - setting the Netis router through the entry site in personal Area Netis.cc. I'll show you how to connect a computer to Netis and configure a WiFi network, as well as how to change the default password and set yours official firmware. Show the whole process will be on the Netis WF2780 router, but in general, the manual is universal for any model -, WF2419E, WF2880, MW5230, WF2180, WF2710, WF2409E and so on.

How to connect a WiFi Netis WF2780 router to the Internet?

In order to go to the personal office of the router Netis, first of all you need to be reset all network configurations on the computer. To do this, come in need to go to the settings. network connections and make sure that all checkboxes are in the "Automatic" mode (IP address, subnet mask and DNS servers)

After that, connect the Netis router to the power out of the power to the power adapter. Insert the cable from the Internet provider to the WAN port (on this model it is blue), and the cable to which you connect the router with a computer - to the LAN port

Entrance to the Netis.cc personal account - 192.168.1.1

To enter the Netis router, launch the browser and go either at a web address. http://netis.cc.Or by the IP of a personal account that is standard by default (do not confuse with the address 192.168.l.l - at the end you need to write the numbers, and not the letters "L").

If before that everything was done correctly, the page will open fast settings - No additional authorization in the administration is not required at the initial stage.

How to set up a Netis router through a personal account 192.168.1.1?

Also, the first thing will be useful so that you can use the username and password from the web interface installed by default from the factory. Perhaps someone has already tried to connect the router and set its parameters.

Connecting the Netis Router to the Internet

All basic Netis settings are immediately on start page. First of all, this is the configuration of the Internet and wireless networks. To connect the router to the Internet, you need to select one of the types:

• Dynamic IP.
• Static IP.
• PPPoe
• Others

What kind of you, you need to look at the contract for the provision of services with the provider - depending on this you will need to enter certain data for the connection. They also need to learn from their operator.

Here you can activate. This is done if the provider binds a specific connected computer to your contract. In this situation, to change it, you need to call technical support. To do this, put a tick on the "Mac clone" and it will automatically be copied from the main computer.

Setup WiFi Netis Network

The next block is the WiFi settings on the Netis router. In my model presented, I have supported two frequency ranges, so you can set the data immediately for two networks. Namely

• Ssid ()
• Security (should be the checkbox on the on)
• Password

Initially, two networks will work simultaneously, but later they can be activated and individually in the extended Netis settings.

After entering all the parameters, press the "Save" button, after which two new devices will appear in the field of visibility with a wireless module wiFi network.

How to change the default password and put your on the Netis router?

Now let's see how to change the password on the WiFi router, which stood by default to connect to your wireless network. Go to the admin partition (how to do it is described) and click on the "Advanced" button

If your two-way router, i.e. distributes the Internet at frequencies of 2.4 and 5 GHz at the same time, you need to understand the password from which name of the diapass you want to change. The settings of each of them are in different subsections of the same name. I will show the example of the example used from them - I open the heading " Wireless mode 2.4 GHz ", section" Wi-Fi settings”.

Here in the "Access Point Safety Parameters" package is looking for a "password" point - it is here that you can prescribe a new key to connect.

To apply the change, click the "Save" button and wait for the router to restart.

Brief instruction on setting up the Netis WF2780 router

So, summarize all of the above in the brief guide, which must be done to install the router.

1. Insert Internet cable to WAN port on the router
2. Connect the marchutizer through the LAN connector to the computer
3. Go to Netis.cc
4. Select the type of connection to the provider
5. Set WiFi network settings

Video on connecting and configuring the Netis router

Eastern users need high-speed Internet access with a stable wireless signal and with a large radius of action, so all additional complex functions are unnecessary. These criteria are fully consistent with the Netis router, which also has an affordable price and high quality assembly. Below is a manual for the connection procedure and setting settings for the example of the Netis WF2411E router.

The web interface of the apparatus is characterized by simplicity and thoughtfulness and, most importantly, it is Russified, so the Netis router setting will not cause difficulties even at novice users.

The following instructions are universally suitable for all Netis models. The Netis router is very easy to connect and in the procedure for entering the settings.

Connection procedure for a PC, laptop or mobile device

Before configuring, the device is required to correctly connect.

It is necessary to carry out the following sequential steps:

The above connection instruction is preferred and will exclude possible malfunctions when the subsequent settings procedure. However, in the absence of a computer, it is possible to enter the necessary parameters to enter the necessary parameters and using the connection of any mobile device to the router via wireless technology. As soon as the router is enabled, it will immediately begin to broadcast its Wi-Fi network with a name, for example, "Netis_C2323B". It is only required to connect to it using the Password code, from a smartphone or tablet and enter the equipment interface. At the bottom of the device enclosure, the name and password for the entrance are written.

Sometimes the specified access codes and login are not triggered. This happens when the equipment has already been tuned and used in the provider's network. In this case, it is recommended to reset the parameters of the apparatus to the factory state. For this purpose, simply by pressing about ten seconds to hold special button "Reset" recessed in the case.

Login to settings

The entry procedure to the router interface does not have absolutely no differences from other routers, so users already having such experience will cope with the process even without instruction.

The following several actions are required:

Setting

Enter quickly settings as follows:

If you need to detailed configuration, you need to click "Advanced".

After that, a window will be displayed with all sections, ordered in the left menu block, and the main interface window serves to enter the functioning parameters.

Section "Network"

The router can function on a wired connection and via Wi-Fi. When booking "Network" is opened a selection of any of these connection methods.

Next, the remaining parameters will appear. For example, in the case of wi-Fi use The network will display a list of networks, and when a cable connection is made, you should select the WAN type. Here is the subsection "LAN", where IP, DHCP is carried out. In some modifications, Netis provides an IPTV connection, which is included with the indication of the "Bridge" mode and the introduction of the LAN connector used.

Wi-Fi-mode

To enter WiFi parameters, you need to enter the "Wireless Mode" section, where to specify the name of the Waifa created, the access code to it, the type of protection of the encryption, the width of the channel, etc.

After completing the adjustments to click on "Save".

In the future, when connecting devices with the created network, you will need to specify the name and password entered in this window, so it is highly recommended to write them in notepad, since even the worst notepad is always better than good memory.