If you turn on the computer writes a message USB Device Over Current Status Detected! System Shut Down After 15 Sec and not loaded, most often the reason for this lies not in malfunction of the motherboard or other components, but in problems with peripheral devices. If you translate an error into Russian, it means that the system has detected a device connected via USB, consuming a lot of current, and therefore the computer will be rebooted after 15 seconds.
Sometimes it can be a simple BIOS failure and restarting the device can really help. But if this did not happen, that is, two options for actions that any user can perform without advanced knowledge of computer equipment.

How to remove the inscription USB Device Over Current Status Detected - System Will Shut Down After 15 SEC.

Step 1. Turn off all USB devices devices - USB flash drives, printer, chamber, mobile phone etc. Even the mouse is worth disconnecting. We only leave the keyboard.

Turn on the PC and look. Error disappeared? Then, in turn, plug each of the devices and repeat the operation. So you can define which of them the perpetrator of the message "USB Device Over Current Status Detected! Computer Shut Down In 15 Seconds. Finding it, carefully inspect the cable - it may be damaged and korotit. Otherwise, you will have to drag it to repair.

Step 2. We try to reset bIOS Parameters. It may have happened a more global PC I / O Failure of the Basic I / O and will be reset to factory settings. Here. The easiest way to do this is: remove the side cover of the case. On the motherboard There is a battery - pull it out. Wait half an hour and put it back.

Error "USB Device Over Current Status Detected" disappeared?! If yes - excellent, but if not - I'm afraid that the situation is bad and most likely have to take the computer in service center. True, I advise you to do this before, attentive to inspect each of the USB ports of the company: if any garbage did not come there, or did the contacts bent.

Sometimes a metal chip or a piece of other conductive material that has fallen into contacts can lead to a closure and, accordingly, the emergence of problems with the work of the PC. In order to clean them, take advantage of some small brush. For example, I use the old toothbrush to clean the USB ports. Just and good!

Usually users do not pay attention to various inscriptions that appear at the moment of pressing the power button and the appearance of the logo. windows downloads. At this point, the system passes the so-called POST procedure and checks the configuration of your PC. In the overwhelming majority, computers pass this test without problems of tens of thousands of times, but still there are cases when something goes wrong. For example, after enabled, the computer itself turns off and the USB Detected USB Detected error appears on the screen. Since this error is accompanied by an emergency disconnection of a computer, few people will ignore what happened. If you suddenly faced the same problem, you may be useful to the following few tips. Theoretically (and practically) they can help you correct the situation with your own efforts, without having to contact the service or to those skilled in the art.

What is USB Device Over Current Status Detected

For reference it is worth noting that this error does not have to appear immediately after the computer is turned on. There are cases when the user works at a computer (watching the video playing games or is engaged in any other affairs for which modern Windows PCs is intended), no one touchs and suddenly its device is turned off, and the USB Detected Error appears on the screen. . In particularly unpleasant cases, the user can notice not only the error on the screen, but also the smell of something burnt.

This error looks like this.

Judging by the text of the error, the problem is in your USB devices. Specificably, some computer component connected via USB is experiencing problems with overload or incorrect power supply. To protect your computer from subsequent damage, the motherboard turns off the PC. If you heard the smell of burned, then some part of your computer has already managed to suffer seriously. Fortunately, computer or connected to it devices are not always burning, so in the overwhelming majority cases, the emergency completion serves as a fuse that relieves you from much more serious headaches.

How to fix USB Detected USB Detected Error Detected

To begin with, try the easiest and most obvious method:

1. Disable all USB devices from your computer. Turn it off, disconnect all cables from all ports, including USB hubs and hubs. Give a computer minute-two to "rest", and then turn it on again. And yes, the keyboard with the mouse is also worth disabled, because they can easily be the source of the problem.
2. Now connect something one to the computer. For example, a mouse. After connecting, work with a PC for a few minutes, watch it work, and then reboot again. Then plug the second device and repeat the process until the celebration is detected.
3. Often the reason for the error described may be physical damage Devices. For example, the keyboard affected by the liquid. The device itself can work, but internal damage can lead to closing or other failures, which pulls the protective disconnection of the PC. When a device is detected, causing failures, try replacing it and watch the work of the computer.

If the search for a faulty USB device did not give results or after replacing the peripherals, the error is further observed, try to correct the situation in another way.

Another nuance that can affect the appearance of the USB Device Over Current Status Detected - USB jumper, namely its incorrect installation or absence in principle.

1. Turn off your computer and disconnect it from power.
2. Open the housing and locate the jumper for USB ports. You need to look for a comb of three connectors, on which the first and second connector are closed. If there are no jumpers, you need to close the specified contacts or move it from the position "2 + 3" to the position "1 + 2".
3. After that, reboot the computer and watch it.

Users can come to mind the idea of \u200b\u200breset BIOS, but it is unlikely that this undertaking will help. Of course, if you changed bIOS settings And after that, an error of USB Device Over Current Status Detected has an error, it makes sense to try to reset the BIOS. You can also roll back it on previous versionIf the problem has started to appear after the update. It is possible that the bug in the software leads to an emergency completion of the computer. It makes sense to check whether the case of your computer with other metal objects does not touch.

If nothing of the specified in this article helped you, you will have to contact the service for the help of specialists. There is a chance that the motherboard itself is damaged due to the jump of electricity, for example.

Some users when enabling a computer can observe the inscription on their monitors - USB Detected USB Detected. Translated from English it means that a USB device has been detected with a large consumption of electricity. When this error appears, you should not immediately open the observation cover. Try to inspect external part system unit.

USB Device Over Current Status Detected Error Solutions

Most often after 2 points applying the reasons, the computer begins to work stably. First of all, you need to try USB ports that are most often used. Usually, these are ports located on the front panel of the computer, take care of them, perhaps you can notice the shades of the car, in this case the port is most likely burned out of overvoltage or improper work. Even if you do not go to determine the visually breakdown, then the sequential disabling devices must be resolved with an error error - USB Device Over Current Status Detected.

Other causes of errors with yusb

This statistics error most often occurs on ASUS motherboard models. There is no need for some errors, including this, immediately contact specialists from the service, because at least half of them any average user can solve independently at home. In the event that the above tips did not come up and the error is not going anyway, it is possible to try to try some more tips:

• You need to reset the BIOS settings. This can be done in several ways: programmatically, using the clrTc jumper, as well as using the battery removal system board. You can read more about these methods on the Internet, each for your model.
• Make sure that the USBPWR power management is present on the motherboard, if not, it may cause USB Device Over Current Status Detected error when the computer is turned on.
• A resistor that checks the presence of voltage on the required port can be faulty as it is the cause of the error described above.

Check motherboard

The problem may wage in the motherboard. Sometimes board manufacturers allow various errors in production, as a result of which they can lead to serious consequences, to unstable ports of ports and even short circuit.

Error USB Device Over Current Status Detected happens with improper arrangement of goodworkers and jumpers. This leads to the fact that the system works stably for some time until the first failure and then all sorts of errors associated with the operation of the plug-in modules begin. In addition to the factory flaw, the motherboard becomes dust after a while. This is all accompanied by a mute signal, malfunctions in the work of the components of the motherboard, as well as the fact that the system at startup is trying to diagnose itself.

• Next, it is necessary, with a completely turned off and a de-energized computer, open the viewing cover and carefully examine the motherboard.
• Inspect the jumpers in USBPower and USBPWR connectors. If they are missing - must be installed.
• It is also necessary to check the places of fastening of the board to system block, Check these sections to the oxidation of the plots.
• Check out all ports and basic components of the motherboard, you may be able to see saturated areas, they may be the result of a closure on the port.

The plumes also need to be checked in the bending areas. Perhaps, on one of these sites, one or several wiring is dangle. In this case, complete to the motherboard are additional loops, if there are no such, you will have to buy new and replace. If the loops are all right, try to disconnect them. Sometimes contacts are clogged with dust and cease to transmit a signal. They need to be removed from the nest to blow and put in place again. After that, put everything in place and spin.

» USB Device Over Current Status Detected What to do and who is to blame

Once I had a problem - a small blow to the computer - it cuts out and no longer turns on - I can not even go to BIOS. The screen burns in an incomprehensible error on the black background of the bios loading - System Will Shut Down After 15 Seconds, and, accordingly, after 15 seconds, the computer is cut down. This error occurs only platas ASUS who themselves are very reliable in the work. So as the first time I met such a mistake, I decided to go in a simple way - it's not all anything else in a computer, but it did not help - only one broom, a video card, the player operatives sound and Other pulled out and disconnected, disabled everything that broke into USB ports and the front panel.

Data manipulation did not help in solving the problem uSB Device Over Current Status Detected - Next that occurred to - reset BIOS. Unfortunately, this manipulation also did not affect the work - the computer did not turn on. Then the vershily in the Internet realized that the problem was quite narrowly located - something happened with some of the USB ports, or its controller, because of which the computer actually does not turn on uSB Device Over Current Status Detectedgets on the screen.

Main reasons uSB Device Over Current Status Detected

Of course, the most serious alignment is the motherboard, it is impossible to exclude it, this alignment can hit the budget, but should not be desirable and first it is worth moving all the other reasons for this error. So:

• turn off everything uSB devices - remove all USB USB flash drives and also turn off the front panel of the computer - there are two uSB port. It is necessary to disable it inside the computer - pulling the corresponding connector from the motherboard. In 80% of cases after data of manipulations, the computer begins to work if not go further:
• We inspect all workers USB ports Behind the presence of damage stuck parts, lumps of dust and so on. All clean, or remove the fault. Sometimes contact is bent in the port and he is korotit on the ground, because of what the error itself occurs uSB Device Over Current Status Detected. We check everything well, clean the dust from the ports with a dry tassel. Moosely the computer must be turned off.
• If the data of manipulation did not help, approach the question dramatically - remove the motherboard from the case and try to start it separately from the case. To do this, we unscrew all the bolts that keep the motherboard, and pull it out of the housing. Itself before that it was necessary to pull out all the attached details - a video card, sound, all connected loops to the motherboard so that nothing bothered to pull it out. Next, we connect the feedback power supply from the power supply, and the small loop to the power supply of the processor and try to run the mother. We clicze the connectors responsible for starting PWRBTN any metal object, and look at the screen. I solved the problem exactly that way - it turned out that one bolt was unscrewed and mocked between the mother and the body, the short USB on the body, after removing the motherboard everything perfectly started.

If after all manipulations, you still burn a mistake uSB Device Over Current Status Detected That is most likely a fault of the resistor, identifying the presence of voltage on one of the ports or you have badly checked. In any case, it remains to be brought to the service. And sometimes it is also worth checking routers