TP-Link routers and modems are well-deservedly popular for their reliability, low cost and ease of management. The instruction is based on the example of the TD-W8960N model.

Before turning on

The main function of the router is to create a local wireless network that connects computers, laptops and mobile gadgets within the home / office. The second, no less important task is to connect this network to the Internet. Therefore, before turning on the router for the first time, it is advisable to have the connection settings with the provider at hand. Usually they are spelled out in the contract or in a separate instruction from the provider. If there are no settings, then when connecting, you need to call technical support and ask for this information.

Before turning on, you need to look at the bottom of the case: in TP-Link models, the following information is needed to configure the router:

IP address: usually 192.168.1.1

Login: admin

Password: admin

If the values ​​in your model are different, it is best to rewrite or remember them beforehand.

Turning on the wireless modem for the first time

1. Connect the ISP data cable to the router. Usually it is a telephone cable (ADSL connection, "leased line"), or an Ethernet wire ("fiber", LAN). If the source of connection is a 3G / 4G modem, then you should connect it to the USB port of the router.

2. Connect the router to the mains: TP-Link comes with a power cable.

Connecting to a router

If everything is in order, then in 20-60 seconds the router is completely ready for work. This time is needed to download the firmware. Indicators - LEDs on the front panel will help you to find out about its performance. By the way, for TP Link routers, these "bulbs" glow with a soft pleasant light, not annoying even in the dark. Indicators are equipped with icons or labels. From left to right:

· Power indicator: when the device is turned on, it should always be on.

· Internet: shows the health of the Internet connection. It does not work when you turn it on for the first time; flickers or stays on in online mode.

· ADSL or LAN; 3G, 4G for Beeline and others mobile operators: depending on the type of provider, indicates the presence of a signal from it. When turned on for the first time, it may flash, or it may be turned off.

WLAN (WiFi / Wireless): access point indicator. Blinks or lights up already at the first connection.

· WDS: not present on all models, it is responsible for expanding the coverage of the wireless network.

· There may be other "lights" - USB port, QSS fast connection, 2-6 local network ports, etc. It is normal for these indicators to be off yet. If the device is used as a repeater, then the light signaling may be different.

Connecting a PC to a wireless network

For settings TP-Link modem a smartphone / tablet will do as well, but we'll look at a good old-fashioned connection from a PC or laptop. If the router is working, then it already "distributes" wireless network(or expands its coverage area using WDS technology). It is called standard and boring - like TP-Link_15616, and is visible from any device. It works without a password and this should be changed as soon as possible.

We connect the computer to new network Wi-Fi. Imp icon wired connection in the Windows tray will be crossed out with a cross (or another icon of the missing Internet).

You can configure your TP-Link router through a browser. We enter 192.168.1.1 (without www) in its address bar: this is the router's control panel. Remember - the IP address plus - the login and password are printed on the bottom of the case? So, instant authorization - and we are in the bowels of the access point. If the ability to change the language is supported, then in the case of TP-Link, this can be done safely: the company is famous for its decent translation of its firmware.

All About Wireless Router Settings

Step by step instructions - connecting to the Internet, setting a network password, advanced parameters: WDS, MAC addresses, connection encryption algorithms.

TP-Link Control Panel Home Page

On the home page(Device Info) nothing can be changed - this is a purely informational section. In the upper part there are information about the firmware and model version, below - the current indicators of the access point and connection with the provider, as well as the date and time.

Attention! When the router is fully configured, all values ​​in the Device Info table should be nonzero. If there are zeros somewhere (or values ​​like 0.0.0.0), something is wrong with the connection. True, a repeater - the mode allows zero values.

How to connect a router to the Internet

Connecting and configuring the Internet takes place in the Quick Setup section of the side menu on the left. On other models, this section may be referred to as WAN Settings / WAN Configurations.

How to connect TP-Link router to the Internet: WAN and ADSL settings

In this section, it all comes down to driving in 2-5 connection parameters that are provided by the provider. In our example, these are:

· Connection method (WAN Link Type): PPPoE mode;

· VPI / VCI values ​​set to 0 and 33;

· Login (PPP Username) and password (PPP Password) for authorization with the provider (not to be confused with the login-password of your personal wireless network!).

Each provider has its own settings: for Beeline they are one, for MTS - others. Although they differ slightly, you should get them exactly from your Internet operator. In any case, to connect the router to the Internet, you need to enter no more than a few values. When the router is acting as a repeater, it should not be configured to connect to the Internet. These parameters are needed only for the access point.

How to set up a wireless network

In the left side menu there is a section called Wireless ("Wireless network", Wi-Fi and other names). We go there.

Basic Wireless Settings Section

Basic wireless parameters of TP-Link router

Basic wireless parameters of TP-Link router:

Enable Wireless: enable wireless network. There must be a check mark.

· Hide SSID Broadcast: hide the network name from the air. The unofficial name of the option is "paranoid mode". With a competent password like 463sltjHe, it is impossible to hack the network, regardless of whether the repeater transmits its name or not.

· Wireless network name: the name of the wireless network. It is better to use something personal to immediately distinguish your own network from the neighbors: The-Best-Wi-Fi, Aleksey's Network, etc. English letters, numbers, spaces are allowed, but - no Cyrillic.

· Country: optional. No country setting is required for TP-Link router to work. You can choose your region, you can forget.

The Apply / Save button is standard for all sections - you need to click it after setting, before moving on to the next section. Attention! Before you change the network name, encryption type, password, WDS mode, etc., keep in mind: the computer will disconnect from Wi-Fi. You just need to re-click on the connection icon in Windows and select the newly created network (enter a new password) for each device on the network. They do not connect on their own.

Security section - security and password Wi-Fi

Perhaps the most important section of the settings. The QSS parameter (in other routers it is more often called WPS) is responsible for quickly connecting new devices to your network by pressing a button, without entering passwords. If we configure the network outside the home (in the office), then it is better to turn it off (disable).

· Network Authentication: type of protection. Remember the word WEP - and never use it at all. WPA only, or WPA2 - no other values ​​are suitable for a secure connection. Valid flavors of WPA type (Home or Enterprise) are also valid. However, there is an ancient belief: a person who does not encrypt his wireless network goes to heaven.

· Setting Open in network encryption means that unauthorized random people can use your Internet, while they can have access to computers on the network. Use it only when you know exactly what you are doing. Even public Wi-Fi networks with free access it is now customary for a cafe / gym to be password protected.

· Wireless Network Key: enter the password for your own network. Do not confuse it with your ISP password. It is this password that will allow other devices to connect to the network. If the device is used as a repeater, then you do not need to set a password. Passwords like 111111, qwerty, Andrey, etc. sooner or later they will definitely be picked up by neighbors. Choose a complex password, with letters, numbers and special characters, at least 10-15 characters.

An old joke: the best password for a computer scientist is the nickname of his pet. After all, a professional IT specialist always calls a dog like [email protected]! kw.

· Encryption algorithm (WPA Encryption). AES and AES-TKIP are equally good, there is no fundamental difference.

Advanced section

Advanced Wi-Fi settings. Useful advancements.

As a rule, advanced settings are not required for TP Link modems. Everything should work with the default values.

2. Mode (mode): b / g / n / ac or their variations - bgn, bg, etc. In fact, generations Wi-Fi standard... You should select the most recent connection mode in the settings, bgn setting, or, if present - bgn + ac. The rest are needed only for rare cases of device incompatibility.

· Ancient and slow a and b-modes are hardly seen even by venerable specialists. Reserved for compatibility and should not be used.

· Old mode "g": can be used if old devices flatly refuse to work with other modes.

· Modern "n" standard: the most common for most devices.

· Ultra-modern "ac" standard: not supported by all devices.

Rarely used settings

Other wireless sections of the TP-Link control panel are required only in special cases - for example, to connect to a VPN, so let's go over them briefly.

MAC Filter - filtering by MAC address. Allows only manually configured devices to connect to the network, and even then after entering a password. No strangers. Not recommended for either home use nor for small office where everyone is yours.

Setting up a VPN on a router: not available on all models. This is a more advanced feature.

Wireless Bridge (WDS): the ability to use a Wi-Fi router as a "repeater" - a repeater of an existing one Wi-Fi signal... It is used to "lengthen" the range of another working and configured router. In other cases, you need to use the already configured AP (Access Point) mode.

Conclusion

Setting up a router is an easy task even for non-specialists, and very, very necessary. Having figured out the parameters once, you will no longer call the masters and customizers - the question is only 2-3 minutes of time.

There is no single instruction for configuring the parameters of wireless networks, but general principles are the same for any model. Only small details differ: some devices use the terms Wireless, others - Wi-Fi; latest models work with the "ac" communication standard, the older ones - with b / g / n-networks. An example of setting up a TP-Link access point is suitable for ASUS devices, and D-Link, and others - only the little things differ. Direct analogy: microwave ovens - the principle is the same, but the buttons are slightly different.

Wireless N Series Router, Up to 300Mbps

tp link-wr841n / tp link-wr841nd

GENERAL DEVICE

1. Device power button.
2. Power socket.
3. Slots for connecting computers via cable.
4. Slot for connecting an Internet cable from a modem.
5. Factory reset button.

CONNECTING A ROUTER

First step. It is necessary to disconnect the modem from the network and remove the backup battery, if used.

NOTE: If you are not using a modem, then immediately connect the Internet cable to the router through slot 4 (blue with the WAN inscription) and skip steps 1 through 3.

Second step... Connect the modem to the tp link-wr841n router through the WAN slot (shown in the picture below) using an internet cable.

Third step... Turn on the modem. Wait 2 minutes and then turn on the router by plugging the power supply into connector 2 and pressing button 1 (shown in the figure).

Fourth step. Check the indicators on the router: if they work as shown below, then the connection is correct.

CONFIGURING THE ROUTER

Method 1 - through the browser.

First. Connect your computer to one of the four slots on the tp link-wr841n router (shown in the figure below) using an internet cable.

Or you can use wireless connection network (SSID). To log in, enter the name and password indicated on the sticker on the bottom of the device.

Second... Open a browser (Chrome, Internet Explorer, Opera, FireFox), enter the following in the address bar: http://tplinkwifi.net.

The following addresses can also be used: http://192.168.0.1/ or http://192.168.1.1/

Then, in the window that appears, you must enter the word "admin" as a login (username) and password.

Click “Login” to enter the router settings.

Further instructions describe two options for debugging the router “Fast” and “Manual”.

QUICK ADJUSTMENT OF PARAMETERS

Third... Select your Country, City, ISP, WAN Connection Type.

ATTENTION: If your internet provider (provider) is not listed,

check the box “I didn’t find any suitable settings” and configure it manually.

Fourth... Check and change the wireless settings if desired.

NOTE: You can set your own name and password for the wireless

networks.

Fifth... Finally, click “Finish” (or “Next”) to save all settings.

MANUAL NETWORK

• In the left column you need to find the "Network" menu item,
• In the appeared internal menu, click on the link "WAN"
• In the “WAN Connection Type” field, select the required connection type.

NOTE: If you do not know which type your ISP is using, it is worth contacting technical support and to clarify this and other parameters required for manual setting router tp link-wr841n.

After completing the required fields, click the “Save” button to save the settings.

MANUAL WIRELESS NETWORK SETUP (wifi)

To change the name of your wireless network, you need to:

• Open the “Wireless” tab in the left menu
• In the opened internal menu, select the item "Wireless Settings"

These will be the settings for the future wifi network.

• First, select in the “Version” field the type “WPA-PSK / WPA2-PSK”
• Then, in the "Encryption" field, set the "TKIP" parameter
• In the “PSK Password” field, enter the password that will protect your network.
• At the end, be sure to save the data by clicking on the “Save” button.

TP-Link largest manufacturer Wi-Fi routers and a number of others computer technology... TP-Link TL WR741ND is a widespread router model for home and office use. Next, let's look at how to set up a router to access the Internet using different types connections, and also give an example of setting up a Wi-Fi network.

Resetting the router settings and connecting to the computer

Since you are about to completely reconfigure your router TP-Link models TL WR741ND, it is best to reset it to factory defaults right away. To do this, take a small object as thick as a needle (the tip of a ballpoint pen is also suitable), and then use it to press the Reset button (see the picture below) located at the back of the router and hold it for a few seconds. The router should be turned on at this moment.

If you notice that all the front bulbs of the device came on at the same time and then went out, then software setting cleared by default - you can continue.
Before setting up the modem, connect the cable that is used to access the Internet to it. It must be connected to the blue WAN port (shown as Internet in the figure). Now let's look at how the setup itself will be done.
Since TP-Link TL WR741ND is a wireless router, you can connect to it via Wi-Fi connection. To do this, you just need to turn on the router, then connect to the Wi-Fi network through a computer or other communication device - a smartphone, tablet, etc. router. In this case, you will not need a password.

If for some reason it is not possible to connect to the router via Wi-Fi, all that remains is to use a cable connection. To do this, one end of the network cable is connected to any of the ports Router Link TL WR741ND, which is yellow, the other end is to the computer's network card. After that, the computer should notify about the connection to local network, and on the router the light under the number of the LAN port to which the cable was connected will blink. However, this does not always happen, so it is better to configure the connection in manual mode... We enter one by one:

If there is no exchange, and command line writes something like "Waiting interval exceeded", you can try again to reset the router settings, check if the wire is connected to it correctly and reconfigure the IP addresses of the computer's network card.

The router is configured via the web interface

Open your existing internet explorer, enter "192.168.0.1" in the address bar. A small dialog will appear in the browser window, in which you will need to enter your username and password. Both are admin by default. Enter them and click "OK".

TP-Link TL WR741ND Supports Multiple Internet Connection Types

Before setting up your device, you need to find out which WAN technology your ISP is using. Below we will consider the most likely connection options, one of which will exactly match your case.

Go to the Network section on the left side of the modem interface, then to WAN. We are interested in WAN Connection Type. Tuning to a particular type of connection always starts from here.

Static IP

The technology is not used very often. Here you just need to ask the provider for 5 network IP addresses (shown in the picture below). Enter them in the appropriate fields and click Save - the configuration is complete.

PPPoE / Russia PPPoE

The technology involves the use of a username and password to access the network. If you know the details, enter them in the appropriate fields: User Name, Password and Confirm Password.

PPPoE is often used with static IP. If your provider issues these addresses to its customers, then they will also need to be entered. To do this, in the Secondary Connection section, move the switch to Static IP and enter the IP address and subnet mask provided by the provider.

Click Save.

L2TP / Russia L2TP

By default, the connection type requires specifying the server address, login and password, as well as (not always) additional network addresses issued by the provider individually to each client.

First, we enter the data in the User Name and Password fields. Then in the "Server IP Address / Name" we enter the server address (also issued by the supplier). It can look like a regular IP-address or like, for example, "adres.provaydera.ru". If your provider has issued additional network addresses, turn on the Static IP item and fill in the fields, as in the case with the Static IP paragraph.

Click Save.

PPTP / Russia PPTP

Another common type of connection. Here, a VPN network is used to connect to the provider. The settings are exactly the same as in the case of L2TP / Russia L2TP described in the previous paragraph. You just have to call your ISP to find out the type of connection they are using.

In the case of TP-Link TL WR741ND, Wi-Fi is easy to install:

All other items can be left as they are.

Click Save. TP-Link TL WR741ND is ready to go! It remains only to check the connection.

TP-LINK is one of the leading manufacturers of network equipment. We will provide detailed information on how to connect or reconfigure a TP-Link router. The procedure for connecting the device, setting up a wired and wireless network, changing the password and updating the firmware will be discussed. The information obtained will allow you to easily perform the configuration home network in TP-Link routers.

What data is needed to connect a router

To change the parameters of the router directly, you need two things: a browser and a password with a login for access. The latest data can be found on a label affixed to the body of the device. As a rule, the standard username and password are the English word admin.

To use the Internet, you will also need authorization data, which you must obtain from your provider. Moreover, they must be spelled out in the service agreement. They must be entered in a router or a specialized program, if such is provided by the provider. Be sure to find out the type of connection (PPPoE, L2TP, PPTP and others) for correct setting... When using dynamic IP, you need to find out your IP address, subnet mask and the like. If all these parameters are already at hand, you can connect TP-Link.

How to connect the device to a network, PC or laptop

The procedure does not cause great difficulties, while it is performed for 5-10 minutes. You should follow the steps of the following instruction one by one:

Wi-Fi models are configurable over the air. This is relevant if you do not have the ability to connect the router to your computer via LAN. This completes the manipulations with the wires. Then the process continues in the web interface.

Login to the web interface

Modem manipulations are performed only in the web interface. It can be accessed from a computer when connected network cable or via wifi on a wireless model. Attention! You can use the interface at any time, even when the Internet is not working. To enter, follow the steps given in the instructions:

Router settings

Let's move on to the most interesting part - changing the parameters of the router. The main window contains more than 10 different sections. Most of them are unnecessary for the average user. Internet activation takes place in a maximum of two sections. Next, we will tell you in detail how to set up a TP-Link router, about creating a wired connection, setting up Wi-Fi, changing the login password and other useful things.

Connecting to a wired network

The router has a quick setup function. This section is recommended for beginners. Click the Next button and follow the prompts from the installer:

When configuring other types of connections, fields for entering a username and password will appear. Here you need to enter the data that the provider will give. The user can change the parameters in the "Network" section. In some TP Link models, next to the connection type selection, there is a “Define” button, which will help you to find out your type. Based on the WAN, the corresponding characteristics are already being configured.

For example, to use PPPoE, fields for login / password and PPPoE-specific parameters already appear in the window.

Wireless connection

For devices with a Wi-Fi module, you will also need to set up a wireless connection. This can be done with a quick setup (the penultimate point assumes the introduction of all important parameters).

Let's see which Wi-Fi settings on a TP-Link router should be changed. Broadcasting should be set to "on". The SSID or network name is what will be displayed on other devices when searching. Enter your region, mixed mode. Leave the channel and its width automatically. Advanced users can choose it on their own, taking into account the busy channels of neighboring routers. If you want to put a password on the access point, select the WPA2-PSK security type. In the end, it remains to enter only the password from the wireless network point. Click the "Next" button and complete the process.

Similar settings can be found in the "Wireless Mode" section. To change the SSID or channel parameters, select the “Settings wireless mode". You can change the password in the "Wireless Security" item. Do not forget to click the "Save" button for any changes. If the selected parameters have not changed, reboot the device.

These menu items are used to configure the TP-Link manufacturer's routers.

Changing the password for logging into the web interface

All owners are advised to change standard password and login from the router. This is due to the fact that an attacker in the absence of a password for Wi-Fi or hacking it will be able to enter the parameters of the modem and "have fun". It will not be difficult to eliminate the problems created, but it is better to avoid this. The interface allows you to quickly and conveniently change the input data:

If you forgot your login information, please do a factory reset.

Advanced settings

The router has a mass additional functions that expand its capabilities. Check out some of the advanced settings:

• Guest network. Allows you to set up a public guest network, restrict incoming / outgoing traffic or uptime.
• Change of addressing. It allows you to set static IP addresses or use DHCP.
• Call forwarding - setting up virtual addresses, web telephony, conferences and the like.
• Functions parental control... Limiting the time of Internet access or specific resources.
• Manual assignment of the routing table (for specialists).
• Binding MAC addresses to specific IPs.

For more information on how to configure the specific functions of your TP-Link router, please refer to the user manual.

VPN

This technology allows you to hide information from prying eyes. Encryption is performed, so that even the provider cannot track your visits. However, only those models with a preinstalled VPN server can use VPN. You can perform the adjustment by the following steps (for English firmware).

The TP-Link TL-WR841N router is one of the most popular router models, which has proven itself from the very best side and, as a result, is consistently in high demand among many users. In this article, we will take a closer look at the procedure for connecting and configuring the router, including, we will tell you in detail about configuring wireless wifi networks.

Brief specifications TP-Link TL-WR841N

Characteristic	Meaning
A type	Wi-Fi router
Wireless standard	IEEE 802.11n, IEEE 802.11g, IEEE 802.11b
Frequency range	2400-2483.5 MHz
Max. wireless speed	300 Mbps
Antenna	2 x 5 dBi
Wireless signal strength	20 dBm
Wireless Security	WEP / WPA / WPA2, WPA-PSK / WPA2-PSK
Ports	4xLAN 100 Mbps, 1xWAN 100 Mbps
VPN pass-through	PPTP, L2TP, IPSec (ESP Head)
DHCP server	there is
Dynamic DNS	DynDns, Comexe, NO-IP
Firewall (FireWall)	there is
NAT	there is
QoS (data prioritization)	WMM, Bandwidth Control
WDS Bridge	there is
Dimensions (WxDxH)	192 x 130 x 33 mm

How to connect a router

The scope of delivery of the router includes:

• Router TL-WR841N;
• Power adapter;
• Ethernet cable with RJ-45 connectors;
• CD for quick setup;
• Management.

We unpack the box and proceed with the installation and connection of the router. First, we connect the device to power using the adapter and press the Power button on the rear panel (if the indicators on the router light up themselves after power is applied, then you do not need to press the button).

Next, using the included Ethernet cable, we connect the router and the computer. We plug one end of the cable into one of the four yellow LAN ports of the router, and the other into the connector network card PC. Then we connect the cable coming from the Internet provider or ADSL modem to the blue WAN connector of the router.

In principle, that's all, now you can proceed directly to setting up the router, but first we will make a reservation that it comes with a CD with a utility that allows you to make quick setup the router step by step. We will not consider this method, because the configuration option via the web interface is preferable.

Basic configuration of the TP-Link TL-WR841N router

Since the router will now be responsible for connecting to the Internet and distributing it, the need for the previously created in Windows high speed connection no. At the same time, a local network connection connecting your computer and router needs to be configured. Go to Control Panel - Network Control Center and general access- Change adapter settings... Right-click on the active connection and select "Properties".

On the “Network” tab, set the switches to “Obtain an IP address automatically” and “Obtain a DNS server address automatically”.

Also in position automatic tuning put the switch on the "Alternative configuration" tab. We save the changes with the "OK" button.

Now we launch any browser and write in the address bar http://tplinklogin.net/ or 192.168.0.1 ... Then, in the window that opens, enter the username and password - by default, this is admin and admin.

The default username and password can be found on a label on the bottom of the router. Look at it and make sure again that all the login details for the TP-Link TL-WR841N web interface are entered correctly.

If everything is done correctly, you will be taken to the administration panel. Here we immediately go to the Internet settings.

Internet setup (WAN)

Select "Network" in the menu on the left (in the English-language interface - Network), and then the WAN section. In the WAN Connection Type drop-down list, select the required type of connection to the provider.

There are the following options:

• Dynamic IP address;
• Static IP address;
• PPPoE;
• L2TP;
• PPTP.

It makes no sense for you to delve into the essence of all these types of connection. Information about which one to choose is provided by the provider. Also, the Internet service provider transmits authorization data to the client - username and password. If you suddenly forgot these data, then they can be spied on in the contract. The second option is to call the provider's support service.

So, we set up a WAN connection according to the following schemes:

• When choosing dynamic IP address no additional action is required;
• Option Static IP address provides for the entry of the IP address, subnet mask, gateway and DNS. We remind you that all this data is provided by the service provider, i.e. your ISP.
• Connection type PPPoE requires a username and password.
• When choosing a connection L2TP the username, password and IP-address / Name of the VPN server are specified.
• Connection type PPTP It will also ask you to enter a username, password and IP address / VPN server name.

After all the data has been entered, click the "Save" button. The Internet should work.

After configuring the Wi-Fi router TP-Link TL-WR841N, there is no Internet access

In case you set everything up clearly according to the instructions, but as a result the Internet does not work, you need to do the following:

If none of the above steps help, the router may be malfunctioning. To make sure the device works, try connecting it with friends or acquaintances.

Wi-Fi setup

Providing opportunity wireless connection to the Internet is one of the most important functions of a router. Let's move on to the Wi-Fi settings for TP-Link TL-WR841N.

We go to the section Wireless - Wireless Settings (Wireless - Wireless Settings). We set the name of our Wi-Fi network and select the region.

Below are network settings that, in certain situations, can affect signal quality and coverage. We will not focus on them, since this is a topic for another big conversation. Leave all parameters at their default values ​​and save the settings.

Now we need to protect our wireless network from unauthorized third-party users. Select the item "Wireless Security" on the left.

Set the switch to "WPA / WPA2 - Personal (recommended)". Next, select the version, encryption type and set the password. We save the changes made.

Setting a new administrator password

The standard username and password for accessing administrative settings makes your TP-Link TL-WR841N router very vulnerable, so it is better to change them immediately. We go along the way System Tools - Password (System Tools - Password). Here we enter the old and new data for authorization (you can only change the password, and leave the username admin), and then click “Save”.

The password can be written down somewhere so as not to forget.

Perhaps on this basic setup Wi-Fi router TP-Link TL-WR841N completed. Of course, there are many more functions that can be useful to users. However, this will be a more subtle configuration, requiring a separate article. We achieved the main goal - we set up the Internet and Wi-Fi.

For all settings to take effect, we restart the router. This can be done programmatically through the section ( System Tools - Reboot) or physically by turning off the power. After downloading, you should see Wi-Fi network with the specified name, to connect to which you will need to enter a password. The Internet must work in both "wired" and wireless modes.