Windows cannot be installed on this drive. Error - Windows cannot be installed on this drive Disk is not included in the bios menu

Or it starts to malfunction and it becomes necessary to install a new one. However, this may be associated with some difficulties. Due to incorrect parameters that can be set through no fault of the user, errors appear that interfere with the normal installation of the operating system Microsoft Windows... Unfortunately, such troubles occur quite often. What to do in such a situation? In this article, we will take a closer look at how to solve the error "Windows cannot be installed on this disk ...", as well as for what reason such a malfunction occurs and what to do about it. Let's figure it out. Go!

If you have an error "The selected disk has a GPT partition style", then you should pay attention to some parameters. For new computers with UEFI that support 64-bit OS, it is better to install on a GPT disk (even if a regular BIOS is not scary instead of UEFI, it is important that there is support for 64-bit systems). For older PCs with a regular BIOS that support only 23-bit OS, it is better to install on MBR disk(done by conversion).

Installing Windows on GPT

Most often, this problem is encountered Windows users 7, however, this does not exclude the possibility of this problem appearing in newer versions of the system. For installation on a GPT disk, be sure to select the 64-bit version of the OS. It should be loaded in EFI mode... Most likely, the error appears precisely because the last condition is not met.

First of all, open the BIOS. This is done by pressing a specific key on the keyboard, depending on the model of the computer, at the time of starting the PC. Usually these are the Del or F2 keys. Once you are in BIOS, change CSM to UEFI boot... You can find this item in the "BIOS Features" section or " BIOS Setup". The next step is to select "AHCI" in the item "Select SATA Operation Mode". In a regular BIOS, go to the "Advanced" tab, in the "AHCI Mode Control" section, set "Manual", and in the "Native AHCI Mode" item that appears below, set "Disabled". For those with Windows 7 or older, you need to turn off Secure Boot.

There are various options for interfaces, so the names of some items may differ slightly, so do not be alarmed if yours coincide with those indicated in the article. Remember to save your changes before exiting. After that, if you installed the OS from disk, the error should no longer appear.

Users who install Windows from a USB stick will likely need to create bootable USB drive again, only now with UEFI support, so that the error disappears. To support UEFI, after you have created a bootable USB flash drive, you need to transfer to it ISO image with the system. You need to do it like this:

  • Mount the image;
  • Select all files and folders of the image;
  • Right-click and from the list that appears, select "Send" and then "Removable Disk".

After that, the installation problems should disappear.

Converting GPT to MBR

Before we move on to analyzing this process, I would like to draw your attention to the fact that it is better to move all data from the HDD, as they may be lost. If you are not worried about the lost files, feel free to proceed to the steps below.

To convert a GPT partition table to an MBR partition table, use the Shift + F10 key combination while in the wizard Windows installations, you need it to run command line... Further, it is necessary to repeat exactly the following steps. Display a list of all disks on the PC, type "diskpart" followed by "listdisk". To select the disk with which you are going to work further, write "select disk M". In place of "M", write the number corresponding to the desired drive. The previous command "list disk" just displayed numbers.

Next, clean up the disk by typing "clean". When the cleanup is complete, enter "convert mbr" to convert GPT to MBR. Please note that with this approach, all data will be lost. At the end, write the command "exit". You can now close the command line or continue working with it to create partitions.

Exists Alternative option which will save all the data. This way is to use special utilities... One of these is MiniTool Partition Wizard Bootable. "Bootable" means that this version can be written to a USB drive (the flash drive must be bootable) and run even if Windows is not working. After downloading, you will see a menu in which you need to select the item corresponding to the name of the utility. Once in the MiniTool Partition Wizard Bootable window, select desired disk and click on "Convert GPT Disk to MBR Disk" on the left. Then click the “Apply” button.

If the system installed on your computer is working properly, then you can download other programs that have similar functionality, for example, Acronis Disk Director or Aomei Partition Assistant... You can also use the built-in Windows tools. To go directly to the desired utility, use the Win + R combination "diskmgmt.msc". Go to the "Disk Management" window, select the drive you want to convert and click "Delete Volume". After that, click on it again with the mouse and click on the item "Convert to MBR disk". Ready.

After reading the above material, you will know what to do if, during the installation of Windows OS, an error message appears that it is impossible to install Windows on this disk. All of the above methods will help you solve the problem. Write in the comments if the article was useful for you and ask if something was not clear.

I have already mentioned in my articles more than once about SSD disk ah, he said that they are faster than usual and with their help you can upgrade your computer. And it would seem that their installation is a trivial thing, what could be easier, remove the old one HDD, install a new SSD , install Windows on it and rejoice, but in reality everything is not so simple. The fact is that in order to squeeze out the maximum speed from an SSD disk (otherwise why use it), you need to switch to AHCI mode(Advanced Host Controller Interface). And here surprises can begin ...

So I have old computer, who decided to upgrade and install an SSD drive. In BIOS I switched the AHCI mode. To do this, I went into the BIOS (press the Del or F2 button (there may be other keys depending on the model motherboard), when you turn on the computer) in the "Main" menu selected "Sata Configuration".

And in "Configure Sata as" I chose "AHCI"

Saved the settings, rebooted the computer, and started installing Windows. But it was not there, an error occurred:

I started to change the BIOS settings, even updated its version , the result was one - this error constantly appeared. As a result, I decided to select IDE mode in BIOS and install Windows.
The installation was successful, then I decided to try switching back to AHCI mode in BIOS, but this trick failed and Windows simply did not boot (in principle, I expected a similar result). Then I decided to do this - switch back to IDE mode, go to Windows and change the mode to ACHI in the registry editor.

After returning to IDE mode, Windows booted successfully, now you need to make changes in the registry. To do this, open the registry editor - press the key combination "Win" + "R" and enter regedit.


In the registry editor, go to the path "HKEY_LOCAL_MACHINE \ System \ CurrentControlSet \ Services \ Msahci", find the "Start" parameter, open it double click... Enter "0" in the Value field.

Everything, the system can be rebooted and set the AHCI mode in the BIOS. As a result, everything worked, the SSD disk worked in ACHI mode. Windows successfully booted and worked many times faster than with a regular hard disk.

So, if your old computer has ceased to please you with its speed work - installation SSD drive, in my opinion, perfect solution... But do not forget about the minimum size. random access memory- 2GB well, and a processor, preferably 2 cores, at least 2 GHz each.

I hope this article helped you avoid the error:

Windows cannot be installed on this disc. Equipment possible this computer does not support booting from this disc. Make sure the controller of this drive is enabled in the menu Computer BIOS.

And it helped upgrade your computer and improve its performance and performance.

You may encounter the message "Windows cannot be installed on this disk" at the stage of selecting the operating system installation partition if not supported loading from the selected data carrier. The reason for such an obstacle is stated in the message of the installer.

Reasons There may be several such problems:

  • worn out or damaged SATA cable;
  • disabled hard disk controller in BIOS;
  • malfunctions the data carrier itself;
  • absence as part of the distribution kit Windows driver AHCI;
  • out of format BIOS - UEFI or Legacy - disk partition style - GPT and MBR, respectively.

Let's talk about the last two problems in more detail.

AHCI problem

The appearance at one time of the mode for connecting the SATA controller of data carriers AHCI, which replaced the old IDE, entailed an additional requirement to the composition of the Windows distribution - the presence of the corresponding driver... AHCI driver support is announced in OS versions starting from Vista.

But not always Windows 7 wants to be installed on a computer with active mode SATA controller AHCI. There are two ways out - distribution change(AHCI drivers can be cut by packers of pirated assemblies) and switching AHCI to the old IDE mode. In the latter case, you need to enter the BIOS, find the section for configuring the parameters of the SATA controller (sections may be called "Integrated Peripherals", "Storage Configuration", etc.) and change the pre-installed AHCI to IDE.

Converting MBR to GPT

Windows will not install if the disk has wrong style sections:

  • GPT, while the UEFI interface is disabled in the BIOS;
  • MBR, while UEFI mode is active and Windows is installed from a bootable UEFI media.

The last case is the most common: everyone who, either replaced motherboard to a new one with BIOS support UEFI, or hooked up for assembling a PC, HDD or SSD disks with MBR markup. There can also be two ways out of the situation:

  • refuse from the benefits of UEFI, disable this interface in BIOS (switch to Legacy) and continue Windows installation to an MBR disk;
  • transform its in GPT.

If there is no important data on the hard disk, transformation from MBR to GPT will be done automatically Windows installer. To do this, at the stage of choosing the location for installing the OS, you need to delete all the partitions that have it.

And as an installation location point out one-piece unoccupied space.

You need to complete the process of reinstalling Windows, return to old system and install this program. Or boot up with LiveDisk with AOMEI Partition Assistant included, if access to old Windows already impossible... The developer of the program - AOMEI company - foresees the ability to create an emergency bootable media with their products on board. To create such media, you need to use another product from the company - AOMEI PE Builder. Also, AOMEI Partition Assistant, among other software for system engineers, is part of LiveDisk AdminPE.

To transform disk from MBR to GPT, follow the steps as in the screenshots below.

After converting the section style again launch Windows installation.

Convert GPT to MBR

If the question is the opposite - for example, the motherboard do not support BIOS UEFI, but the component assembly included an HDD or SSD with GPT markup, there will be nothing left but transform its in the MBR. This can be done in the same ways as described above for the reverse process:

  • the way deleting all partitions using the Windows installer, if there is no need for the data stored on the disk;
  • by using programs AOMEI Partition Assistant.

To convert a disk from GPT to MBR, follow the same steps as in previous section articles, with the only difference that this time we launch, respectively, the reverse operation.

"" Error "Windows cannot be installed on this disk"

Error "Windows cannot be installed on this disk"

Sometimes, when installing Windows 7, 8 or 10, you may encounter a problem, which is that when you try to install the system on a hard disk, the system issues a warning: “Windows cannot be installed on this disk. Your computer's hardware may not support booting from this disc. Make sure the controller of this drive is enabled in the menu Computer BIOS ".

The problem is usually typical for old computers and laptops, but occasionally manifests itself on new hardware. This usually happens if the mode is enabled in the computer's BIOS settings in the hard disk parameters. AHCI or something other than IDE... Therefore, we go to BIOS computer and set the operating mode of our disk as IDE. Typically, this setting is located in the section IntegratedPeripherals or Advanced, and she herself is usually called SATARAID /AHCIMode, SATAMode, SATAAHCIMode,ConfigureSATA or another name with a similar meaning.

I also met this way of deactivating the mode:

  1. Switching the operating mode using the setting AHCI Mode Control into mode Manual.
  2. At the same time, the setting becomes available to us Native AHCI Mode which we must switch to Disabled.

During the installation of the operating room Windows systems 10, various errors can occur. As a rule, they are associated with incorrect BIOS settings or incorrect work components of a computer or laptop. One of frequent mistakes sounds like: “Windows cannot be installed on this disc. Your computer's hardware may not support booting from this disc. Make sure the controller for this drive is enabled in the BIOS menu of your computer. " Yes, there are troubles when the disk is really cut off and no longer works. But more often than not, the reason is different.

The most common reason for this malfunction is the settings of the SATA controller when working with old hard drives. Try to start, when you turn on the PC, go into the BIOS and change the controller operation mode from ACHI to IDE.

On more modern motherboards with UEFI instead of the regular BIOS, switching to Legacy mode may help.

If none of these manipulations helps, then return everything as it was. The reason is most likely different.

Sometimes the error "Make sure that the controller of this disk is enabled in the BIOS menu of the computer" may appear because the boot record is crooked hard disk and it needs to be restored. To do this, when starting the installation of the Windows 10 operating system, click on the "System Restore" button and go to the "Diagnostics" >> "Advanced options" >> "Command Prompt" menu, or simply press the Shift + F10 key combination. A black Windows console window will appear:

In turn, we type the commands:

Bootrec / fixmbr bootrec / fixboot bootrec / RebuildBcd

Each of them should complete successfully. After that, we restart the PC and try to start the installation again. This is usually a disk controller error in bios menu the computer is solved and then everything goes on without any problems.

set-os.ru

Windows cannot be installed to disk

During the installation of the operating system, at the stage of formatting disks and creating partitions, the user may encounter the error “Installing Windows on this disk is not possible. The computer hardware may not support booting from this disc. Make sure the controller for this drive is enabled in the BIOS menu of your computer. "

Why does this error occur and how to fix it?

See also: Codes Windows errors 10 and how to troubleshoot

Ways to solve the problem

Often, the error when it is impossible to create a partition to install a new operating system occurs on old PCs with Windows 7. However, other operating systems, from XP to Windows 10, are also not immune from such a problem.

The following factors can be the cause of this error:

  • Incorrect settings of SATA parameters;
  • Hardware specifics (availability of additional SSD and SCSI cards).

Method number 1. Via BIOS settings

To fix this error, it is worth booting into the BIOS and setting the hard mode IDE drive... To do this, do the following:

  • Reboot the PC and press "F8" several times to get into the BIOS.
  • Find the section "Advanced" or "Integrated Peripherals" and select the item "SATA Mode" or "SATA Raid", "Configuration SATA" (the path to the settings depends on the motherboard model). We change the mode of work with AHCI or another on the IDE.

  • We press "F10" and restart the PC. We repeat the installation of the system.

If your PC has new firmware BIOS, you should enable EFI boot instead of IDE mode. To do this, do the following:

  • Boot into BOIS-UEFI and go to the "Boot" section. We find the item "UEFI / Legasy Boot" and set "Enabled".

  • We save the changes and restart the PC.

It should be noted that with this change, it is possible that new error which is associated with MBR or GTP partitions.

See also: How to install Windows 10 to a GPT and MBR disk?

If your PC or laptop has an additional cached SSD or other storage device, it may be the cause of the problem. To fix the problem, follow these steps:

  • We determine the model and version of the device. Go to the developer's site and download the drivers, which are sealed in the archive, and not laid out in a separate exe file.
  • We unpack the files to a USB flash drive.
  • We start the Windows installation. At the stage of choosing a volume, click on the "Load drivers" button.

  • A new window will open. Click the "Browse" button and specify the path to the drivers. Click "Ok" and "Next".

  • We try again to select a volume for installing the system.

Method number 3. If the error is related to the GPT or MBR format

If during the installation of Windows 7, 8 or 10 you get the error “Windows cannot be installed on this disk. The selected disk has a GPT partition style ", it is worth changing GPT format on the MBR. To do this, we perform the following actions.

  • We save all data from the C drive, as it will be formatted. It also does not hurt to save information with local disk D.
  • Open the command line with administrator rights and enter the following commands in order:
  1. diskpart;
  2. list disk;
  3. select disk № (indicate the number of the disk on which you will install Windows and with which problems arise);
  4. clean (the entire disk will be cleaned);
  5. convert mbr (format changed);
  6. exit.

After formatting the partition, it is worth rebooting the PC and trying to install the OS again.

You can also perform the same steps more in a simple way... In the BIOS in the "Boot" section in the "UEFI / Legasy Boot" item and set Enabled, and in "Secure Boot" - Disabled. After that, we delete all sections and create new ones. The format will be automatically changed.

SoftikBox.com

Windows cannot be installed on this disc. Check BIOS setup


Comments on record: 4

Hello everybody! When installing Windows on a laptop, I got an error: Windows cannot be installed on this disk. Your computer's hardware may not support booting from this disc. Make sure the controller for this disk is enabled in the BIOS menu of your computer.

I read it on the Internet, someone says that you need to switch from achi to ide. Switched over - did not help. Looked bios settings, well, in the laptop it is so simple that there is almost nothing to choose at all ... Resetting the Bios did not help ... Then I inserted the Windows disk back and pressed the system restore during installation (this is where the install button is). I chose a team building. By the way, you can run it Shift + F10.

We write bootrec / fixboot. Then we try to install. It helped me.

The fact is that Windows could not find the bootloader and did not understand what to do. This is how the error is solved, installing windows on this disk is impossible.

AlexZsoft.ru

Windows cannot be installed on this disc.

At reinstalling Windows 7, an unexpected problem arose on the laptop - the BIOS and the Windows installer saw the hard drive, it was allowed to mark it, add / remove partitions, but then it did not go further, giving out a strange-looking message:

Windows cannot be installed on this disc. Your computer's hardware may not support booting from this disc. Make sure the controller for this drive is enabled in the BIOS menu of your computer.

Why is it strange? In general, support for the AHCI (Advanced Host Controller Interface) mechanism has been announced since Windows Vista and installation disk with Windows 7 licensed.

Well, God bless him, you can look for the guilty for a long time and persistently, but it's easier to get into the BIOS and switch AHCI Mode Control c to. Then it will be possible to disable Native AHCI Mode. Subsequently, you can return the settings back by installing the system and all drivers.

If you find the article useful, do not be lazy to like and share with your friends.

mdex-nn.ru

Windows cannot be installed on this disk (solution) - Programming, administration, IT

Windows cannot be installed on this disc (solution)

This manual provides details on what to do if during Windows installation you are told that it is impossible to install Windows on a disk partition, and in detail - “Windows cannot be installed on this disk. The computer hardware may not support booting from this disc. Make sure the controller for this drive is enabled in the BIOS menu of your computer. "

If you do select this section and click "Next" in the installer, you will see an error stating that we could not create a new or find an existing section, prompting you to view additional information in the installer log files. Below we will describe how to fix this error (which can occur in Windows 10 - Windows 7 setup programs).

As more and more often on computers and laptops of users there is a variety in disk partition tables (GPT and MBR), modes HDD operation(AHCI and IDE) and boot types (EFI and Legacy), errors during the installation of Windows 10, 8 or Windows 7 caused by these parameters are also increasing. The described case is just one of such errors.

Correcting the error "Installation on this disk is not possible" using BIOS settings (UEFI)

Often specified error occurs when installing Windows 7 on old computers with BIOS and Legacy boot, in cases where the BIOS is in the operating parameters of SATA devices (i.e. hard disk) in the AHCI mode (or any RAID modes, SCSI).

The solution in this particular case is to go into the BIOS parameters and change the mode work hard disk to IDE. As a rule, this is done somewhere in the Integrated Peripherals - SATA section Mode settings BIOS (some examples in the screenshot).

But even if you don't have an “old” computer or laptop, this option can also work. If you are installing Windows 10 or 8, then instead of enabling IDE mode, I recommend:

  1. Enable EFI Boot in UEFI (if supported).
  2. Boot from the installation drive (flash drive) and try the installation.

True, in this version you may encounter another type of error, the text of which will inform you that the selected disk contains an MBR partition table (the instructions for fixing are mentioned at the beginning of this article).

Why this is happening, I myself did not fully understand (after all, the AHCI drivers are included in Windows images 7 and higher). Moreover, I was able to reproduce the error for installing Windows 10 (screenshots are just from there) - just changing the disk controller from IDE to SCSI for virtual machine Hyper-V "first generation" (ie with BIOS).

Whether the specified error will appear during EFI boot and installation on a disk operating in IDE mode, I could not check, but I admit it (in this case, we try to enable AHCI for SATA disks in UEFI).

Third-party disk controller drivers AHCI, SCSI, RAID

In some cases, the problem is caused by the specificity of the user's equipment. The most common options are having caching SSDs on a laptop, multi-disk configurations, RAID arrays, and SCSI cards.

SIMILAR ARTICLES