Your question:

How to change the Nokia Case?

Master's answer:

Today, our lives is almost impossible to imagine without a mobile phone, which has quite firmly entered the human resource. With it, we are given the opportunity not only to communicate with close people who are in any end of the planet, but be aware of all the news of interest, as well as send letters to e-mail. However, from frequent use by the phone, its body very soon comes to disrepair. In this case, it is necessary to replace it. How to do it?

Here, of course, we will need a manual nokia phone 3250, small screwdrivers in a set, plastic opener and screwdriver, tweezers.

Before you begin to replace the housing, you need to lay the tissue of white or other, but mandatory light color on the table, but you can also use white paper sheets in order for the parts of a very small size well visible. In addition, it is necessary in that place where you will disassemble the phone, the lighting was good.

For a start, it is necessary to get acquainted with the Nokia 3250 instruction manual. If you do not have a guide, you can download it on the official site of Nokia.

Actually, the process of replacing the case consists of parsing the lower and upper parts of the phone. To do this, you need to turn off the phone. Then you need to remove the lid of the battery compartment and get the acumulator. Then remove the SIM card and USB flash drive from your apparatus. The bottom of the phone is deployed so that it becomes perpendicular to the top. A pre-prepared plastic opener hook the bottom end of the phone. As a result of your actions, he will be removed from the latch and will open. In no case do not attempt to use scum or any other sharp object for this purpose, since there is a possibility to break the phone body. In this case, you can only use a plastic opener. Then you need to remove the facing rim at the top. Get the keyboard. After you remove the keyboard, at the bottom of the middle will see a piece of black scotch, the top of which you need to neatly rejuvenate. The keyboard loop is located under it. In order to remove it from the connector, you need to push the screwdriver on both sides. Then you should unscrew the screws that are also on both sides from above, as a result of which the lower part separates from the top. Then at the bottom you need to remove the side sites.

Then the plastic plug is carefully satisfying the front of the screen in several places. It is necessary to do it smoothly, so as not to damage the plastic latches. After that, you need to remove the buttons under the screen. Remove the plastic head of the plastic phone out of the top. Under it, you will see screws located along the edges in the amount of 4 pieces. Next, you need to pose a plate with a screen located on the keyboard side and lift it perpendicular to the case. The loop under it should be disconnected and then get the display. Under the display in the middle there is a window where two more loops are located. They also need to be disconnected. In order to finally remove old housing, I need to pull for it, while holding the inner parts of the phone.

When you replace the old details of the case to the new, the phone must be collected, but only already in reverse order. In the case of buying a new case of another color, you also need to buy a suitable keyboard, as they are usually coming separately.

one of the most common needs of owners of mobile phones. Not always falls are fatal, most often cracked or scratches appear on the housing. Some users Nokiaimmediately go to the store to buy a new, beautiful, while it is hard to use the old one. Who will be nice to use a broken device? But do not get upset, as there is always a way out.

Why is it necessary to replace the Nokia case?

Despite the fact that today there are many accessories that your need to remove Nokia from shocks, phones suffer most of all from physical damage. If you dropped it at home on a carpet or any soft surface, nothing terrible will happen to him. If you dropped a cell on the street, he hit, for example, on asphalt - the consequences will be much more serious. The case can split or completely crash and it will be necessary change Nokia Phone Case.

What to do? Output:

Depending on the damage and phone model, you can try to try yourself. replace Nokia Corps. In our service center, you can purchase all the necessary spare parts. But in the case of deep deformations, it is best to replacing the Nokia panel was produced by our experts, since modern cellular is quite complicated electronic device. There used to be very popular with non-removable covers, which were well coped with their task and were releasing cellular from severe damage, while maintaining a commodity view. But they did not very comfortable the use of the keyboard, hiding his features. That is why fewer users continue to use this accessory, and more and more replacing the Nokia panel.

An example from life:

Girl walking, talked on the phone. By chance Nokia.slipped out of the hands and fell on the asphalt. The appearance no longer allowed to continue its operation. Without a long rapidly, she asked for help in our service centerwhere specialists have made diagnostics in 20 minutes and determined that the internal components were not affected. Nokia Case Change She took just a few minutes. The girl received a guarantee for the entire device.

That is why it is not worth spending time in vain. Contact your service center for help. We have:

The diagnosis is completely free and in most cases is carried out in the presence of the client. Is carried out on professional equipment;

The warranty is issued to the entire device in the implementation of any repairs, and not only the part installed during the replacement;

After repair or replacement of components, free quality control is undergoing;

Discounts for repair;

Spare parts are only original. We are suppliers of spare parts for the whole of Russia, so the prices for repairs are cheaper.

After the first repair, you are issued a Customer VIP card for a discount from 10% -40%

The best service conditions only in our service!

Hello everyone. Another translation of the official service manual L1-L2. So, our Nokia C5 00 phone has broken the screen, or you need to change the case or trouble with a speaker, a camera, charging connector :) We must disassemble and repair. Start.

A warning

This article is not a guide to action! All responsibility for the collection and analysis of your device lies with you.
Many manufacturers do not bear warranty obligations if the device has been disassembled by the user. If you do not want to lose guarantees in your device, specify the terms of warranty obligations in the documentation or manufacturer of the device.

Used tools

The first step, remove the lid of the battery compartment and take the battery. The cover is removed after pressing the button.

Then remove the plastic lining near the camera, to do this insert the tool for parsing the housings between the overlay and the center panel and use the panel, this should separate the latches marked with arrows. After the marked latches are disconnected, raise the upload up for a bent end, the aspension is separated on the opposite side of the lining. In the official manual, it is written that the tool for the parsing should be installed not as in the figure, this is an erroneous photo, but there are no other yet :)

Remove the lining.

Unscrew two screws under the lining, in order indicated in the picture.

We remove the front panel, to do this insert the tool for parsing the housings into the slot between the front and the central panels in the place indicated in the picture, and we move it in the direction indicated by the long arrow. Do not try to remove the panel after that, you can break the remaining latches.

We continue to disconnect the latches on the other side and from the bottom end.

Now you can remove the front panel.

Start a protective film on display.

Press the keyboard from the outside to get it out of the front panel.

The keyboard is removed.

Remove 5 screws in the order specified in the picture.

The motherboard holds in the housing on two latches. Bend the first latch to the tool for paving the enclosures.

Then beate the second, from the opposite side.

Remove motherboard From the housing.

Remove the antenna module.

Tool for paving the enclosures. Patient keyboard loop connector.

Remove the metal frame with a keyboard substrate.

Pretty display loop connector.

Remove the display.

Remove the rubber chamber sealer.

Remove the camera module. This requires a special tool, but you can do and flat screwdriver.

The camera is removed.

Remove the power connector from the housing using the charging connector.

By analogy with the power connector, remove the 3.5 mm connector from the audio-video housing.

Remove the SD card slot door.

Remove the speaker.

It is convenient to get a tweezers speaker.

Patty the keyboard substrate.

A tool for paving the enclosures. Off the keyboard substrate from the metal screen.

Do not forget to access the back of the screen.

Remove the keyboard substrate. In theory, it cannot be reused.

Assembly tips.

Tighten 5 screws in the manner specified in the picture with a moment 17 NSM.

The remaining two screws are tightened in the manner indicated in the picture with torque of 14 NSM.

The rest of the assembly is simply in the reverse order.

Thank you for your attention and a good day!

Articles and Lifehaki

To update the appearance of the mobile phone, there is such a procedure as replacing phone cases. The case is the detail of the phone that is most often exposed to different mechanical damage. This not only makes your device not too presentable, but can also negatively affect his work. Is there any condition of the body on, there is no information.

What is the replacement of the mobile phone housing

Do not everyone know that the casing is different from replacing the phone panels. Panels change much easier. Often, the replaceable panels of different colors are sold along with the phone itself, it allows you to quickly change your device beyond recognition. Panels are attached on the phone only with the help of plastic latches, housing - and with the help of latches, and miniature screws.

If you threatened to change the case on your device, you need to stick to a number of rules:

It is advisable to acquire original parts. This will allow you to be confident that they are ideal for your device model.
- It is necessary to check: all the details are connected without the slightest gaps, there is no scratch on the plastic or glass of the screen, all the fasteners are working.
- An independent replacement of phone packages requires special tools that must be approached under the sizes of screws inside the device.

How to replace the housing

Usually, when the plastic breakdown on the phone, a broken touch screen or with numerous scratches, spoiling it appearanceThe owners of the devices appear in the service center. Sometimes here, unexpectedly, they will know, that is, it can only work with a SIM card of a certain operator.

But repair can be done on your own, if you know how to keep a screwdriver in your hands.

1. Disconnect the phone, remove rear panel And remove the battery.
2. Carefully unscrew the screws under the panel.
3. Remove the housing. If it is a touch panel - it is usually bonded by glue. To remove it, the glue needs to soften, heating it with a hairdryer.
4. After removing the touch panel, the remaining glue must be read and then apply a fresh layer. If he is soft and not lost his adhesive properties - you can attach a new panel to it.
5. The display is usually attached by screws, so when it is replaced with a new screwdriver.
6. In place of the old building, we place a new, checking that it clearly entered into all the available grooves.
7. Screw the screws.
8. Check the operation of all telephone mechanisms - screen, buttons, make the screen calibration.

If your mobile phone works - you coped with the repair yourself.

I haven't purchased myself so long ago new phone from the firm already loved me Nokia. - but for the second card, left his old and dyed time Nokia 6300.. And now I do not use it as I decided to press the use, good people. And other day I decided to transform (reanimate) both externally and internally, for which it was decided to buy a new contest, and then update the firmware. For all your time my work Nokia 6300. I threw a lot of shocks, there were drops, and shattered several times, but never broke and did not give up for repair. With the exception of the fact that the corps scattered and broke it finally, at the beginning she stuck with the most universal tool Scotch tape, then decided to disassemble, clean the body and stuck super glue, but still for some reason the type of device did not suit me. I started looking for a new building, but what I did not take everything was made not qualitatively, although the sellers argued that the corps is original, it was also clear that the building of Chinese origin, and everything is also made bad, with plastic serifs, not docks and different flaws . But then I caught more than a good hull.

Today I will tell you about how to replace the building on Nokia 6300., then try to show the easiest way to update the firmware on Nokia 6300..

Case replacement on Nokia 6300

In order to replace the housing, you need the following:

• Phone itself
• Screwdriver Set
• Mediator
• New housing

Of course, the mediator here is an optional tool, but it is great for removing the old housing, as it is thin in thickness and allows you to get into inaccessible places and at the same time not strongly damage the old case.

Now you need to open rear cover The housing, where two bolts will be visible at the bottom, which need to be unscrewed, thereby unscrewing the front face part of the case.

After that, you need to take the mediator, and carefully remove the facial part of the case, for which you need to pose a rivet on the side, along the entire surface of the top of the case, after which the front side of the case must be disconnected itself.

Now you need to unscrew the four bolts located around the display.

And the mediator will come in handy again, in order to remove from the main part of the case, the main phone board together with the display.

Under the main board, there is an iron plate, which is unfortunately in the new building I have no, so it needs to be removed, for which a small screwdriver is useful. But before removing the plate, you need to remove small white pieces of plastics, which are located on the sides of the case, and the LEDs are covered, usually blinking when the call is missed. All over the perimeter of the iron plate, there are a number of different rivets that you need to pose the whole screwdriver.

At the next stage, you will need to remove the power socket, for which you need to insert the plug from charging into the socket and lift a little, so the nest will be ready to install it in a new case.

Now you need to carefully remove the microphone, and without damaging it. For what you need carefully a screwdriver to hide the microphone, after which it will fall out of the nest.

Now you need to remove a large block, which is located on the top of the case, and contains speakers, antenna and other important elements.

Under a large block with details, a protective grid for a speaker is glued to the housing, which unfortunately was also absent in the new building. Therefore, it needs to be removed and cleaned from dust and dirt.

As it was possible to notice from previous photos, under the case due to its not tightness, accumulated a large number of Dust and dirt. Therefore, now all the details must be cleaned and alternately start inserting into a new building.

First you need to insert the iron plate, the lateral plastic elements.
Then you need to glue the protective grid for the speaker. Then insert or native or from the new housing of the shutdown button and adjust the volume. And then insert the upper block with speakers and antenna.
And only after this you need to insert a power connector, a microphone, the cover for the MINI-USB connector at the bottom of the case.

First you need to fasten the main board of the device to the housing to two bolts, and turn on the phone to check the performance of all newly inserted elements. After that, four bolts need to fasten the main unit of the device.

At the last stage of the enclosure, you need to insert the front panel of the case along with the keyboard, then under the cover of the body, turn the last two bolts, after which the housing can be considered successfully installed.
In general, in the assembly of all the details and insert them into a new building, I think there should not be problems, since when disassembling the body, the location of all items and order I think that should be deposited in memory.
After all the details were inserted into a new case, the phone instantly transformed and began to look like a new one.

Repair Connector for headset on Nokia 6300

The only thing that distinguished this phone from the new, this is what the headphone jack did not work. Inside the connector there are several iron elements that need to make something thin, for example needle. It's just that the connector can be said over time, the iron elements are pressed into the body of the connector, and the needy can be renewed back to the center of the connector. After that the connector will work.

Firmware update on Nokia 6300

The firmware update on the phone is desirable to perform regularly, since the manufacturer is often in new firmware corrects some disadvantages and not refinement.
In order to update the firmware you need to download and install special software from the official site of Nokia. What you need to go to the following address - http://www.nokia.ua/support/software/phone-software-update. Where you need to choose the model of the phone, in this case This is Nokia 6300.
The page uses two options for downloading and updating the phone firmware:

• with Nokia Ovi Suite
• using Nokia Software Updater

In our case, we will use nokia program Software Updater ( Nokia PZ NOKIA), and to download it in the drop-down list you need to select the program language you need, then click on the button Zavanceriti Or go to the following address - http://nds1.nokia.com/files/support/global/phones/software/nokiasoftwareUpdatersetup_ru.exe.

After that you need to run installation file.where in the first window will need to read the prompts and click on the button Continuation of installation.

The next window will be proposed for reading the text of the license where you need to click on the button. Further.

The next window will display the installation process, which lasts about two minutes.

In the last window will be displayed additional Information On the installation of this software, where you need to click on the kopk Ready.

On this installation software Nokia Software UpdaterNow you need to run the program.
Please note that to update the firmware on the phone, need to have access to the Internet as new firmware will be downloaded from the official site.
After all the above, you need to start the program where the program reference information and the update process will be displayed in the first window, where you want to click on the button. Start.

Before updating the firmware on the phone, you need to make a backup of all data, and the main contact list is saved, as it will be deleted. You also need to make sure that the battery charge is full.
Now you need to turn on the mode on the phone Normal, then connect the device to a computer using a mini-USB cable, and click on the button Further.

In the course of the update, the program will display text prompts, so it will be difficult to get confused.
The next window will display the text to read and agree with the consent. It says that you are confident that all data is saved and done backup copy, and that is not a password on the memory card. And it is also warned again that all data from the phone will be deleted. Here you need to check the box and click on the button Reinstall.

The next window will display the update process that is approximately 15 minutes.

If everything went successfully, then the next window will feature the information that the firmware is successful and the device can be used.

This update firmware and replacing the housing on the Nokia 6300 is over.
Some of these instructions can be applied to other models of phones of the company.

Now my phones look like this:

Good use!