Modern DVD players are quite complicated. technical devices, their work is determined not only by the design and elemental base, but also software. In the course of continuing to improve the consumer qualities of its products, BBK Electronics can make some changes to the DVD player software.
At IT Slanga, such software is usually called the firmware (eng. Firmware - built-in, "stitched", "covered" inside by). If the device works normally and no complaints, then it does not make any sense to change the firmware. However, if the manufacturer corrected the errors of the previous software or added new features, the ability to update the firmware seems to be tempting, taking into account that there is nothing difficult in this if you have strictly follow the instructions.
Perhaps for your device update software Not relevant - During pre-sale preparation, DVD players are equipped with last version BY. Compare the software version of the software presented in this section and the version number installed in your machine. You can find out the software version in the player service menu: Press "SETUP" - the menu is displayed on the screen, section "Main Settings" page, type the "9210" combination digit key - the player's service menu will appear on the screen, the Version line displays the installed software number provision.
Attention! When the software is replaced, the device may fail. We strongly recommend producing this procedure under the BBK service center. If for any reason you can't contact service centerYou can produce this procedure yourself, strictly following the instructions below.
Instructions for creating a disk with software:
- Download the program "Nero Burning ROM" (from http://www.nero.com/).
- Install the program.
- Download and unzip the DV925HD DVD player software.
- Change the file name on DV925HD.BIN
- Attention! Do not make any changes to the software file - this will lead to the output of the player fail!
- Install the pure CD-R- or CD-RW disk.
- Run "Nero", a dialog box appears, select "COMPILE A NEW CD" and click "Next\u003e"; In the next window, select "Data CD" and click "Next\u003e"; Next, select "CREATE A NEW DATA CD?", Then "Next\u003e" and "FINISH".
- The main program window will appear, divided into two parts, in the right part, locate the software file (DV925HD.BIN) and drag it with the left in the left, then go to the "Edit" menu and select the "Properties" section.
- Navigate to the "ISO" tab and set the settings in accordance with the picture:
- After completing the settings, go to the "File" menu and select "Write CD". In the dialog box that appears, select the desired write speed and click the "Burn" button.
- After successful recording, the appropriate message appears on the screen, click "OK", close the dialog box, the disk will be automatically removed from the drive.
Software Replacement Instructions:
During software replacement provide power stability DVD player - Disable electricity and voltage drops can lead to the output of the player.
- Press the "POWER" button. The DVD player will turn on, "No Disc" appears on the DVD player display.
- Click the "OPEN / CLOSE" button. The tray for loading the disk is promoted.
- Put in the tray disk with the inscription software up.
- Click the "OPEN / CLOSE" button. The tray closes. "Loading" will appear on the TV screen.
- After a few seconds, an inscription will appear on the TV screen:
"Upgrade File Detected
Upgrade?
Press Play to Start. "
Click the "Play" button. - At the bottom of the screen (under the "Press Play to Start" line), "File Copying" appears, which will change the "Upgrading" after a few seconds.
- The tray will automatically advance, remove the disk from the tray and wait a while on the TV screen will not appear the standard BBK screensaver ("BBK DVD Video" on a blue background) and the tray will not automatically close. In the upper left corner of the screen, "Loading" will appear, which will change to "No Disc" after a few seconds. This means that the software replacement has passed successfully and the player is ready for work.
Supplement: from the BBK forum again about updating the firmware.
The firmware update is done like this - the file is unzipped, then this file is renamed, for example, the name of the DV718SI-1A-1031 file, you renamed in the "DV718SI.BIN" then the parameters are displayed in Nero
ISO - MODE1, ISO 9660 ONLY, MAX OF 11 \u003d 8 + 3, remove all checkboxes ... throw the file in Nero and burn ..... Everything is ready!
(By the way, do not press anything during flashing, the disk should go out, and until the BBK screensaver appears, do not touch anything and not press, otherwise it is a threatening device !!!) "
+ Add to this that if you have a CD-RW drive in the settings, put "without multi-session"
Boldly use CD-RW, you can always correct the incorrect file name. If there are no errors in installations when recording a disk in Nero, the DV923HD.bin file must be perceived
You can record several different files on the disk at once, the player itself will find the appropriate file name.
Firmware (Firmware) is a software that is actually an operating system of the device ( bIOS microcircuits, DVD drive, modem, player, mobile phone …).
The firmware is also called the file that contains updated version Programs for upgrading the device.
The firmware is sometimes called the Firmware Program (Flasher), designed to download this file in the Flash memory of the device.
The firmware is also the process of loading the program to the device.
In the software execution, the firmware, as a rule, is a binary file (with the * .bin extension), less commonly executed file * .exe.
Why need firmware update (flashing)
There are many reasons why you have to update the firmware (Firmware):
- for compatibility with new software (for example, with new OS);
- to increase device performance;
- to expand configuration capabilities (add new features);
- to correct errors and flaws of the drive software (eliminate glitches and bugs);
- to remove the binding to the region (setting the multizoneity of the drive);
- To change the ID String drive (for example, the firmware from KISS will show the drive as KISS, and not as Toshiba);
- to remove the ripple;
- …
How to make a backup of the original firmware
To save copies of the original firmware apply special programsFor example, binflash.
Run the program, make sure that the drive is selected from which you want to make a backup.
Select the DUMP option.
Assign the file name for your backup.
What is riplock and what is it needed for what
Riplock (Riplock) is blocking the drive speed for some types of disks. Riplock was conceived as one of the methods of combating video samples: it does not allow you to quickly copy the videos (this is its main purpose).
Another purpose of the ripple is a decrease in noise level when playing DVD films.
In most riplock firmware, it is removed, which provides high rap speeds, but it usually takes place only for stamped DVDs.
Removing the ripple can make your drive more "noisy" when playing on PC stamped DVDs.
What is RPC-1 and RPC-2
There are two types of DVD drives:
RPC-1. (Region FREE) - free from regional protection (so-called multi-zone);
RPC-2. (Region Protection) - with regional protection.
Even for RPC-1 drives, it is sometimes required to remove binding to the region to play a DVD.
Firmware programs (flash drives) are for DOS, and for Windows.
DVD-drive firmware from DOS
Insert a 3.5-inch floppy disk in the floppy disk (see, sometimes they can still be useful about it!).
- Open My Computer, right-click the 3.5 drive, select Format from the context menu.
- Window The format disk 3.5 (A :).
- Choose formatting method - Creating boot disk MS-DOS (Check box).
Click Start - OK.
At the same time, files will be copied to the disk:
Display.sys.
EGA2.CPI
EGA3.CPI
EGA.cpi.
Keyb.com.
Keyboard.sys.
Keybrd2.sys.
Keybrd3.sys
Keybrd4.sys.
Mode.com.
- Find the firmware for your DVD drive.
Start searching the firmware follows from the manufacturer of the drive manufacturer.
Original firmware are called Original Firmware.
- Download the firmware, unpack the archived file (in the archive, as a rule:
README - instruction,
Update.Bat - batch file for launching a firmware,
v ******. Exe - Flasher,
******. Bin - firmware).
- Copy Update.Bat, V ****** files. EXE, ******. BIN on the boot diskette.
- Restart PC. When rebooting, press the DELETE key to enter into utility BIOS. SETUP.
- Install the first boot device of the floppy drive (1st boot device - floppy drive).
- After loading the PC from the diskette, the system A: \\\u003e will appear
- Enter Update.Bat (can be lower case and without expansion - Update), press ENTER.
- If a message appears that the Update file is not found to find a packet file on a diskette to start the firmware, enter the DIR, press ENTER.
- Flasher will boot (for example, the TOSHIBA ODD-DVD SD-M1802 flash drive when loading will display the following information: *** Flash Program to Upgrade SD-M1802 ...).
- It will be prompted to click any key - Press Any Key to Continue ...
- Flasher scan drives.
- the tray of the flashing drive will be prompted, and a message will appear:
OVER WRITE FLASH-ROM? (Y / N):
Enter Y, press ENTER.
- The process of flash firmware will begin (the firmware duration is on average 1.5-2 minutes).
- In case of successful firmware, the drive tray closes, a message appears with the drive name and the firmware number.
- After inviting the system A: \\\u003e, click Reset.
- When rebooting, press the Delete key to enter the BIOS SETUP utility.
- Install the first boot device Winchester (1st Boot Device - Hard Drive).
- Press, authorize saving changes.
- After loading operating system A message appears that new equipment has been found - dVD drive.
OS will pick up the driver from his library for him.
You can use the drive!
Firmware DVD drive from Windows
- Open the tray of the reflamped DVD drive.
- Run the flash drive (there are universal flash drives, for example, Flasher SFDNWIN_3.25.4 is designed for the firmware of TOSHIBA and Samsung drives).
- In the DRIVE drop-down list, select the desired drive.
- Click the button Download file. Open.
- In the Open window, specify the location of the firmware.
If this firmware does not suit this drive, the Message window will appear with the error message "File Open Fail (NO Flash File)! 0b 0kb 0cmd. "
- Press the "Start Download" button.
Attention!
1. Firmware DVD drives (however, and other iron too!) - Potentially dangerous and difficult to predictive occupation!
If the drive is warranty, can it be easier to contact the store or service center?
2. Even use original firmware (from the drive manufacturer) does not guarantee the integrity and performance of the DVD drive after the firmware.
3. Try to find the firmware for your DVD-drive model. If the firmware is used from the same manufacturer, but for another model, the results may be unpredictable!
4. Do not close the drive tray and do not restart the PC in order to avoid damaging DVD drive!
5. If the PC hangs during the firmware, press RESET (or turn off the PC and turn on again).
6. If, after firmware and restart the PC, the DVD drive will stop responding (it may not be determined even at the BIOS level!), Turn off the PC and turn on again.
7. The DOS DVD firmware is considered more reliable than from Windows.
Auto note
There is a problem: the discs recorded on some drives are sometimes not read on other drives (the main reason for this is "scattering" parameters of drives and disks).
However, this is not a drive malfunction and, probably, this is not a reason for flashing.
As a rule, the flashing is solved already when "got glitches and bugs", i.e. When there is nothing to lose ...
Therefore, before you decide on flashing, think carefully!
To save copies of the original firmware, you can use the BINFLASH program.
Download and install it.
Run the program, select Drive for Bacup.
Select the DUMP option.
The file selection dialog box appears.
Select the file name to copy the original firmware.
Press SAVE and wait until the backup process is completed.
We emphasize once again that even the use of the original firmware (from the drive manufacturer!) Does not guarantee (!) Integrity and efficiency of the DVD drive after the firmware.
Those. The result of flashing may be such a situation that the drive will have to just throw out!
Driver AMD Radeon. Software ADRENALIN EDITION 19.9.2 Optional
The new version of the AMD Radeon Software Adrenalin Edition driver 19.9.2 Optional increases the performance in the Borderlands 3 game and adds support for Radeon Image Sharpening Image Correction Technology.
The owners of the DVD-Players of these series are very often faced with the problem of the absence of support for Cyrillic, as a result, any Russian names of media files on media are displayed by "hieroglyphs", even despite the Russified menu. In this article, I will tell you how to correctly flash the Pioneer DVD player DV-400/410/420/600/610 with support for Cyrillic.
This information is designed primarily for newcomers, therefore replete large quantity Screenshotov I. detailed description Actions that the usual user may seem at absolutely not requiring comments. Please treat with understanding.
1. And so, open a web browser and go to the Pioneiro FAQ site, in particular, in the firmware section, as shown in Figure 1 with a red marker.
Picture 1.
2. In the list of firmware, we find your DVD player model. This article describes the player firmware. Pioneer DV-420As shown in Figure 2 Purple Marker. If desired, of course, you can enter any firmware from models. DV-400/410/420/600/610Since they are mutually replaced. It is important to note when firmware player series DV-4XX. Firmware OT. DV-6XX.there will be no sound at analog DVD player entrance, and remove sound track It will be possible only from a digital entrance!
We are interested in firmware with support for Cyrillic (CP1251), marked with a red marker in Figure 2. In the list of firmware of this type, select the latest version - in this case V2.0.As shown in a blue rectangle. Press the right mouse button on the link.
In addition, the firmware with support for Cyrillic can be downloaded from here. 
Figure 2.
3. In the menu that appears, select Save the link as ...
Figure 3.
4. Now you need to select the path to the folder in which we save the firmware, and then click the button Save.
Figure 4.
5. Now you need to turn on the DVD player, and go to Home Menu. By pressing the control panel of the same name. In the menu you need to go to the function Source settingsAs shown in Figure 5 with a red marker. 
Figure 5.
6. We see a window with settings. Here I choose item Parametersmarked in red in Figure 6. 
Figure 6.
7. Then, on the player control panel, you must press the key Display.After that, information about the version of the current firmware appears at the bottom of the window, as shown in Figure 7 with a red marker. In this case, the firmware version has a version YJB8A13A.. 
Figure 7.
8. Now we return to the firmware downloaded from the site. An example is shown in Figure 8. 
Figure 8.
9. Next, you need to unpack the archive with the firmware. Press the right mouse button on the file and, in the window that appears, select the item Extract to the current folder.
Figure 9.
10. We see, new files appeared in the folder. We are interested in the extension file * .bin. - This is the firmware. 
Figure 10.
11. In order for the DVD player correctly recognized the firmware, it is necessary to rename it in accordance with the following instruction. Remember the firmware version that this moment Installed in the player, has the form - YJB8A13A.. We choose the firmware you downloaded, and we rename it in such a way that the first three characters are identical to the sewn into the player. In other words, if the downloaded firmware took the form Ykf9930a.bin., then after renaming, should look like Yjb9930a.bin.. An example is shown in Figure 11. 
Figure 11.
12. Now run Nero Burning ROM. By selecting the appropriate item in the menu Start - ProgramsAs shown in Figure 12. 
Figure 12.
13. Next, insert the CD into the CD Disk Drive. After that, in the window that appears, go to the point Create context menu FileAs shown in Figure 13. 
Figure 13.
14. In the new project creation window that appears, check that the CD type is selected by CD, as shown in the picture with a red marker. Be sure to install the checkbox No Multisessionwhich circled in blue. After that, go to the tab ISO..
Figure 14.
15. Be sure to check that your settings be in accordance with the following:
- Data Mode: MODE 1.
- File system: Only ISO 9660.
- File name length (ISO): Max. from 11 \u003d 8 + 3 sims. (Level 1)
- Symbol set (ISO): ISO 9660 (ISO CD-ROM standard)
Figure 15. 16. Here you choose the item ManualAs shown in Figure 16 in red. Then, in the input field, designated in blue, you must enter the following header of the disk:
The code: Pioneer.
Note, the title is entered strictly in capital letters. After that, go to the tab Record.
Figure 16. 17. Here you check the presence of checkboxes opposite the items Record and Finalize CD.As marked in red in the figure below. Then, put the minimum-available Record speedwe have she - 4x (600 KB). Record Method Exhibiting as Disc-AT-Once. After that, press the button NewThe collapsed purple rectangle in Figure 17.
Figure 17. 18. A window appears where you can select the files to write to the disk. On the right side of the window, select the folder where the file is firmware, as shown in Figure 18 in blue. Holding left button Mice, drag the firmware into the left of our window. As a result, it should turn out as shown in Figure 18 with a red marker. After the proceeds done, click the icon Big On the toolbar isolated with purple color.
Figure 18. 19. In the project recording window that appears, press the button Big As shown in Figure 19.
Figure 19. 20. Before us - the recording status window. Install the checkbox opposite the function Check zap. DanyaAs shown in Figure 20 in red.
Figure 20. 21. We are waiting for the completion of the record and verify the project. After that, we see a window with the appropriate information, where you need to click OK.
Figure 21. 22. In the window that appears, press the button Done.
Figure 22. 23. Now insert the recorded disk in the DVD player. After that, a message should appear on the screen that the firmware file is detected and you must click the button. Play. On the control panel.
Figure 23. 24. Press the button Play., after which you see a message about the start of the update process.
Attention! During the update process, you cannot press any buttons, including the control panel buttons!
Figure 24. 25. At a certain stage of the firmware, the system will automatically open the CD-ROM drive tray. Without pressing anything, you can remove the CD. After that, it is necessary to wait for the appearance of the screensaver as shown in Figure 25. Then, turn off the player by pressing the button Standby / ON.. Next, you must enable it, dropping all the settings to the factory. To do this, simultaneously press the buttons Standby / ON. and Stop. And wait for the appearance of a familiar screensaver.
Figure 25. 26. Next, press the button Home Menu. control panel, and go to the function Source settingsAs shown in Figure 26 with a red marker.
Figure 26. 27. Then choose the item Parametersmarked in red in Figure 27.
Figure 27. 28. After that, on the control panel, press the button Display.. At the bottom will appear a new version Firmware, it means everything is done in accordance with the instructions.
Figure 28. 29. We see current firmware Correctly displays Cyrillic characters in file names on CDs. See Figure 29.
Figure 29. 30. In addition, the Cyrillic file names on flash cards are also displayed correctly.
Figure 30. Any copying of materials is allowed only indicating the active reference to the original source
What is the firmware
Firmware (firmware.) Is a software that is actually an operating system of the device (chip Bios., DVD.- Review, modem, mobile phone ...).
Firmware Also called the file that contains the updated version of the program to upgrade the device.
Firmware Sometimes they call the firmware program (flash drive), designed to download this file in Flash.- Device devices.
Firmware The program of loading the program into the device itself is called.
In the software execution, the firmware, as a rule, is a binary file (with an extension *. bin.), less commonly executed file *. eXE.
Why need firmware update (flashing)
There are many reasons why you have to update the firmware ( firmware.):
- for compatibility with new software (for example, with new);
- to increase device performance;
- to expand configuration capabilities (add new "");
- to correct errors and flaws of the software drive (eliminate "and" ");
- to remove the binding to the region (setting the multizoneity of the drive);
- for change ID String Drive (for example, firmware DVD.-Privode Toshiba.from Kiss. will show the drive as Kiss., not like Toshiba.);
- to remove the ripple;
– …
How to make a backup of the original firmware
To save copies of the original firmware, special programs are used, for example, Binflash.:
- Run the program, make sure that the drive from which you want to make a backup is selected;
- Select the option Dump;
- Restart . When rebooting, press the key. Delete. For entry B. BIOS Setup..
- Install the first boot device ( 1st Boot Device. – Floppy Drive.).
- click F10, Saving changes.
- After loading System invitation will appear from the diskette A: \\\u003e
- Enter Update.Bat. (can be lettered and without expansion - update.), click ENTER.
- If a message appears that the file update. not found to find the file to start the firmware on the diskette dir.
- Flash heer will be loaded (for example, a flash drive for drive TOSHIBA ODD-DVD SD-M1802 When loading, the following information displays: *** Flash Program to Upgrade SD-M1802 ...).
- It will be prompted to press any key - Press Any Key to Continue…
- Flasher scans drives.
- the tray of the flash drive will be prompted and the message " OVER WRITE FLASH-ROM? (Y / N)».
- Enter Y., click ENTER.
- The process of the actuator firmware will begin (the duration of the firmware on average 1.5 - 2 minutes).
- In case of successful firmware, the drive tray closes, a message appears with the drive name and the firmware number.
- after inviting the system A: \\\u003e click Reset..
- When rebooting, press the key. Delete. For entry B. BIOS Setup..
- Install the first boot device Winchester ( 1st Boot Device - Hard Drive).
- click F10, Saving changes.
- After loading the operating system, a message appears that new equipment has been found - drive DVD.. It will pick up for him from his library. You can use the drive!
Firmware DVD.- Exercise from Windows
- Open the tray of the reflamp DVD.- Exercise.
- Start the flash drive (there are universal flash drives, such as a flash drive sFDNWIN._3.25.4 Designed for firmware drives Toshiba. and Samsung).
- in the drop-down list Drive. Select the desired drive.
- Click the button Download File Open..
- In the window Open Specify the location of the firmware. If this firmware does not suit this drive, a window will appear Message with an error message "File Open Fail (No Flash File) !! 0B 0KB 0CMD ».
- Press the button Start Download.
Attention!
1. Firmware DVD.- Exercises (however, the other "Iron" too!) - Potentially dangerous and difficult to predictive occupation! If the drive is under warranty, it may be easier to contact the store or
Modern DVD players are quite complex technical devices, their work is determined not only by the design and element base, but also software. In the course of continuing to improve the consumer qualities of its products, BBK Electronics can make some changes to the DVD player software.
At IT Slanga, such software is usually called the firmware (eng. Firmware - built-in, "stitched", "covered" inside by). If the device works normally and no complaints, then it does not make any sense to change the firmware. However, if the manufacturer corrected the errors of the previous software or added new features, the ability to update the firmware seems to be tempting, taking into account that there is nothing difficult in this if you have strictly follow the instructions.
Perhaps, for your device, software update is not relevant - during pre-sale preparation, DVD players are equipped with the latest version of software. Compare the software version of the software presented in this section and the version number installed in your machine. You can find out the software version in the player service menu: Press "SETUP" - the menu is displayed on the screen, section "Main Settings" page, type the "9210" combination digit key - the player's service menu will appear on the screen, the Version line displays the installed software number provision.
Attention! When the software is replaced, the device may fail. We strongly recommend producing this procedure under the BBK service center. If for some reason you cannot contact the service center, then you can produce this procedure yourself, strictly following the instructions below.
Instructions for creating a disk with software:
- Download the program "Nero Burning ROM" (from http://www.nero.com/).
- Install the program.
- Download and unzip the DV925HD DVD player software.
- Change the file name on DV925HD.BIN
- Attention! Do not make any changes to the software file - this will lead to the output of the player fail!
- Install the pure CD-R- or CD-RW disk.
- Run "Nero", a dialog box appears, select "COMPILE A NEW CD" and click "Next\u003e"; In the next window, select "Data CD" and click "Next\u003e"; Next, select "CREATE A NEW DATA CD?", Then "Next\u003e" and "FINISH".
- The main program window will appear, divided into two parts, in the right part, locate the software file (DV925HD.BIN) and drag it with the left in the left, then go to the "Edit" menu and select the "Properties" section.
- Navigate to the "ISO" tab and set the settings in accordance with the picture:
- After completing the settings, go to the "File" menu and select "Write CD". In the dialog box that appears, select the desired write speed and click the "Burn" button.
- After successful recording, the appropriate message appears on the screen, click "OK", close the dialog box, the disk will be automatically removed from the drive.
Software Replacement Instructions:
During software replacement provide power stability DVD player - Disable electricity and voltage drops can lead to the output of the player.
- Press the "POWER" button. The DVD player will turn on, "No Disc" appears on the DVD player display.
- Click the "OPEN / CLOSE" button. The tray for loading the disk is promoted.
- Put in the tray disk with the inscription software up.
- Click the "OPEN / CLOSE" button. The tray closes. "Loading" will appear on the TV screen.
- After a few seconds, an inscription will appear on the TV screen:
"Upgrade File Detected
Upgrade?
Press Play to Start. "
Click the "Play" button. - At the bottom of the screen (under the "Press Play to Start" line), "File Copying" appears, which will change the "Upgrading" after a few seconds.
- The tray will automatically advance, remove the disk from the tray and wait a while on the TV screen will not appear the standard BBK screensaver ("BBK DVD Video" on a blue background) and the tray will not automatically close. In the upper left corner of the screen, "Loading" will appear, which will change to "No Disc" after a few seconds. This means that the software replacement has passed successfully and the player is ready for work.
Supplement: from the BBK forum again about updating the firmware.
The firmware update is done like this - the file is unzipped, then this file is renamed, for example, the name of the DV718SI-1A-1031 file, you renamed in the "DV718SI.BIN" then the parameters are displayed in Nero
ISO - MODE1, ISO 9660 ONLY, MAX OF 11 \u003d 8 + 3, remove all checkboxes ... throw the file in Nero and burn ..... Everything is ready!
(By the way, do not press anything during flashing, the disk should go out, and until the BBK screensaver appears, do not touch anything and not press, otherwise it is a threatening device !!!) "
+ Add to this that if you have a CD-RW drive in the settings, put "without multi-session"
Boldly use CD-RW, you can always correct the incorrect file name. If there are no errors in installations when recording a disk in Nero, the DV923HD.bin file must be perceived
You can record several different files on the disk at once, the player itself will find the appropriate file name.
